Monday, November 17, 2014
Where Is the Fuel Pump Switch on a 1991 Ford Explorer
The fuel pump switch is also known as the inertia switch, a device that prevents fuel from going to the engine if your 1991 Ford Explorer happens to get into a collision. It also enables the fuel pressure to be relieved.
Location
The inertia switch can be found mounted on the floor pan on the passenger side inside your Explorer; look below the heater unit. It will have an electrical connector attached to it.
Servicing the Fuel System
Disconnect the electrical connector that is attached to the inertia switch when performing a task such as relieving the fuel pressure on your Ford Explorer. Whenever youve finished servicing the fuel system, reattach the electrical connector to the switch. You do not need any tool for removing and attaching the connector.
Reset Button
The inertia switch also has a reset button at the top to use in the event the switch was activated during a procedure like relieving the fuel pressure, which would create a popping-like sound. Simply push the button to reset the switch if this occurs.
Monday, December 16, 2013
Ford Explorer Transfer Case Troubleshooting
The Ford Explorer was first manufactured in 1991 and is still in production as of 2011. The transfer case conveys power from the transmission to the axles and can be changed from two-wheel drive to four-wheel drive. Problems with this part makes the vehicle virtually unusable. Several issues can be averted with the careful application of preventative maintenance, but when trouble starts you can at least diagnose the most likely reason for the difficulty.
Instructions
- 1
Drive the vehicle slowly and attempt to engage the four wheel drive through all gears: "2H", "4H", "N", and "4L". Noisiness, jumping out of gear or difficulty shifting indicates further inspection and testing is needed.
2Place the vehicle on a hard level surface and set the parking brake. Engage the drive through all gears with the Explorer stationary. The shifter should work smoothly through all four settings. Difficulty shifting and noisiness requires investigation of the components. The linkage might be loose, bent or binding in movement. Any of the parts in the transfer case may be worn or damaged. These all indicate further troubleshooting is needed.
3Jack up the vehicle and place it jack stands. The transfer case is located between the transmission and the rear axle. Check for any leaks or fluid in or around the transfer case, but particularly around the front and rear shafts because they both have seals that can be worn. Locate the transfer case fill plug. It is behind the transfer case damper if installed. If so, remove the damper. Remove the plug and insert your little finger to measure. The lubricant should be at or just below the bottom edge of the plug hole.
4Remove the transfer case to ensure the components inside are not damaged or misaligned. Where equipped, remove the skid plate. If the damper is still in place, remove it. Drain the lubricant by removing the drain plug on the bottom of the transfer case. Remove the electrical connector, if installed, then remove the speed sensor and speedometer cable from the case. Disconnect both drive shafts. Remove the mounting bracket for the electrical connector, or the vent hose from the shift lever on manual models. For manual models, remove the nut from the shift lever and remove it and the bolts holding the shifter to the extension housing.
5Place a transmission jack under the transfer case and lift it slightly so that you can use safety chains to attach the case to the jack. Remove the five bolts holding the case, and slide the case down and away from the vehicle. Remove and discard the gasket between the case and the extension housing. Inspect all parts for wear, breakage, misplacement or misalignment. Any parts with those signs must be replaced before reinstalling the transfer case.
Saturday, November 16, 2013
How to Troubleshoot Electrical in a 1992 Ford Explorer
The 1992 Ford Explorer has an electrical system which consist of a power generating device, power distribution conductors, a power storage device, safety fuses and the various loads or devices that are powered by 12 volts DC electrical current. Electrical problems are one of the most common problems with cars. Knowing how to troubleshoot electrical problems with the 1992 Ford Explorer is a valuable skill and can provide significant cost savings as well.
Instructions
- 1
Start the Ford Explorer engine and listen to the sound generated by the engine. A slow cranking engine or an engine that wont crank is indicative of a problem with the car battery or starter motor.
2Turn on the radio and listen to its sound. Press the horn button and listen to the intensity of the sound coming from the horn. Turn on the windshield wipers and then switch the wipers off after a few turns. Any noticeable decline in the performance of the above devices, or their failure to operate, indicates a problem with the battery or alternator, or a blown fuse.
3Set the dial of the multimeter to 12 volts DC range. Place the tip of the red multimeter probe on top of the batterys positive (red) terminal. Place the tip of the black probe on top of the black (negative) terminal, and look at the multimeter. The multimeter should give a reading of 12.5 to 12.8 volts with the engine off. A lower reading indicates the battery has low charge and needs recharging.
4Start the car engine and keep the engine idling. Hold the probes of the multimeter on each hand, and place the tip of the red probe on the batterys red (positive) terminal. Touch the tip of the black (negative) terminal with the black probe, and look at the multimeter. A multimeter reading of 13.6 to 14.3 volts is indicative of an alternator that is charging the battery sufficiently. A lower reading is indicative of a defective alternator.
5Read the owners manual of the 1992 Explorer to know the ampere rating of its alternator. Ask a helper to step on the accelerator gently and increase the vehicles idle speed to 1,200 RPM. Hold the probes of the multimeter on each hand, and place the tip of the red probe on the batterys red (positive) terminal. Touch the tip of the black (negative) terminal with the black probe, and look at the multimeter. The multimeter should display a reading equivalent to the ampere rating stated in the Explorers owners manual. Have the alternator repaired in case the multimeter displays a different figure.
6Open the hood of the car, turn off the engine, and inspect the battery terminals. Look for corrosion or a build-up of white substance on each terminal. Corrosion or acid build-up on the terminals will cause poor contact between the terminal and the battery cable, thus preventing power from running from the battery to the various electrical devices including the starter. Clean the battery terminals to ensure the battery operates properly.
7Read the vehicle owners manual to know the location of the fuse box. The Explorers fuse box is typically found under the hood or under the dash. On the lid of the fuse box note the diagram that indicates the fuse position of each particular circuit. In case a particular device is not working, locate the position of the fuse inside the fuse box by reading the labels in the diagram. Replace the fuse with one of equal amperage If the wire in the fuse is broken or appears blackened.
Sunday, October 27, 2013
Explorer Third Row Power Seat Problems
The Explorer, a mid-size sports utility vehicle manufactured by the Ford Motor Company, has experienced a variety of issues related to its third-row seating. These problems vary from minor inconveniences to major issues that may pose safety concerns and necessitate the replacement of the entire seat.
Seat Wont Elevate
Most Ford Explorers are equipped with power seating. Power seating allows the user to adjust the seat to meet their individual preferences through the push of a button, permitting the user to raise, lower or move their seat forward or backward. When the seat will not elevate, a common culprit is a bad motor gear. Over time, the motor that is responsible for allowing the seat raise or move forward or backward may become worn, causing failure of the motor to operate properly. When this occurs, it is oftentimes necessary for the motor to be replaced in order for the seat to operate properly.
Heated Seats
The Ford Explorer also offered heated seats on both driver and passenger seats. While heated seats can be an added luxury, heated seats that fail to work properly can sometimes present a safety hazard. In order to operate the heat feature on the Ford Explorer, the user must push the heat activation button located on the instrument panel on the side of the seat. To turn the heat option off, the button should be pressed again. If the heat fails to shut off, this may indicate a wiring issue that is preventing the heat option from deactivating. Heated seats that fail to shut off on command can lead to serious burns and may need to be replaced in order to prevent harm.
Seats Wont Fold
Another common problem with Ford Explorer third row seating is seats that will not fold down into the floor in order to create a cargo area. When this occurs, a common culprit is head rests that are not folded down enough to allow the seat to collapse. Pulling the black tab forward under both headrests should allow the headrest to fold down completely. From there, try to fold the seats down as usual. If the seats fail to fold after ensuring that your headrests are fully folded, this may indicate a problem with the release, which will need to be inspected by a certified mechanic to determine whether or not the seat is repairable or will need to be replaced.
Thursday, October 3, 2013
How to Replace the Oil Pump in a 1993 Ford Explorer
The oil pump in the 1993 Ford Explorer is a sump pump. This means the pump submerges into the oil in the oil pan and the pump pushes oil to the engine. This is a lot of work for a small pump. Over time, the pump weakens and the engine does not get the oil it needs to run properly. If this happens, you must replace the oil pump. Unfortunately, this task is labor intensive because you must remove the oil pan to get to the pump.
Instructions
- 1
Drive the Ford Explorer onto a set of ramps. Shut off the engine and set the parking brake for safety.
2Open the engine hood and remove the oil filler cap and oil dipstick.
3Place a drain pan under the oil pan drain plug and remove the plug using a socket and ratchet. Drain the oil into the drain pan and then insert the drain plug and tighten it.
4Remove the bolts that secure the oil pan to the bottom of the engine block, using your socket and ratchet. Pry the pan free from the block using a metal scraper and then pull the pan out from under the Explorer.
5Unplug the wiring harness connected to the oil pump.
6Remove the jam nut that secures the oil pump to the oil pickup tube using an adjustable wrench. Turn the pump counterclockwise to remove it from the oil pickup tube.
7Thread the new oil pump onto the oil pickup tube and tighten it using the jam nut and the adjustable wrench.
8Plug the wiring harness back into the oil pump.
9Scrape the old gasket material off the mating surfaces of the engine block and the oil pan. Wipe any old oil off the mating surfaces using a clean shop towel.
10Place the gasket onto the mating surface of the oil pan, place the oil pan against the bottom of the engine block and, using the socket and ratchet, secure the pan to the block. Tighten the bolts in an alternating pattern from side to side.
11Place a funnel into the oil filler spout and pour four quarts of oil into the engine.
12Release the parking brake and drive the Ford off the ramps onto level ground. Shut off the engine and let it cool. Using the oil dipstick, check the oil level and add oil as needed. Replace the dipstick and filler cap.
Wednesday, September 25, 2013
How to Replace O2 Sensors in a 1997 Ford Explorer
Your 1997 Ford Explorer has two oxygen sensors built into the exhaust system. The oxygen sensors monitor the amount of oxygen in the exhaust to help the truck regulate how much fuel it burns. When an oxygen sensor fails, your truck may burn more fuel than necessary, reducing your fuel mileage drastically. You can replace the oxygen sensors quickly in your own driveway. Buy new sensors from an auto parts store or a Ford dealership.
Instructions
- 1
Raise your Explorer with a jack and secure it on a set of jack stands. Locate the oxygen sensors on the exhaust positioned before and after the catalytic converter.
2Disconnect the wiring harness from the oxygen sensor by pulling the connector straight off. Use an oxygen sensor socket and ratchet to remove the oxygen sensor from the exhaust pipe.
3Install the new oxygen sensor by hand to avoid cross threading the sensor. Once the sensor is secure, tighten it with the oxygen sensor socket and ratchet.
4Press the wiring harness connector onto the new sensor until it is secure. The wiring harness should click when it is secure.
5Repeat the process for the second oxygen sensor if you are replacing both. Raise the vehicle with the jack and remove the jack stands. Lower the truck to the ground.