Showing posts with label 1993. Show all posts
Showing posts with label 1993. Show all posts

Wednesday, April 30, 2014

How to Remove the Steering Column Cover From the 1993 Eagle Vision

Youll need to remove the steering column cover, in order to make repairs on your 1993 Eagle Visions ignition switch, steering column or dashboard. This cover surrounds the top and bottom of steering column and includes a hole on the right side for the ignition switch. The cover is made up of two separate pieces that snap together. The bottom piece is secured to the underside of the steering column with three Torx screws.

Instructions

Removal

    1

    Shift the vehicle into park and remove the keys from the ignition. Pry the hazard light switch button from the button assembly on top of the steering column with a flat-head screwdriver.

    2

    Tilt the steering wheel to its highest position. Wrap a shop rag around the tilt lever and grip it with a locking pliers. Lock the pliers on the lever, then unscrew the lever and remove it from the column.

    3

    Remove the screws on the underside of the column shroud with a ratchet and a Torx bit.

    4

    Pull down on the bottom shroud to separate it from the top shroud. Slide the bottom shroud down and off of the ignition switch.

    5

    Screw the tilt lever into the adjuster two to three revolutions, adjust the steering wheel downward, and then remove the top shroud piece.

Installation

    6

    Set the top shroud piece into position, then tilt the steering wheel upward and unscrew the tilt lever.

    7

    Slide the bottom shroud over the ignition switch and into position beneath the top shroud. Press the two shroud pieces together so they snap into place.

    8

    Reinstall the Torx screws on the bottom shroud piece.

    9

    Screw the tilt lever into the tilt mechanism, then wrap it with a shop towel and clamp a locking pliers onto the lever. Screw the tilt lever into place until snug with the locking pliers.

    10

    Tilt the steering wheel downward and set the hazard light button into position. Press down on the hazard light button until it snaps onto the hazard light switch.

Read More.. >

Sunday, April 27, 2014

How to Replace the Catalytic Converter on a 1993 Saturn SL2

The catalytic converter on your Saturn SL2 bolts to a flange on the rear of the head pipe coming off the engine. A clogged converter can cause the engine to run very rough and will build up excessive amounts of heat under your car, which can radiate into the passenger compartment through the floorboards. While many people shy away from exhaust work, you can change the converter at home in the driveway and save yourself a potentially large repair bill.

Instructions

    1

    Position a jack under the front of your SL2 and raise the front end off the ground so you can work underneath it. Place a set of jack stands under the front suspension then lower the jack, allowing the car to settle onto the jack stands.

    2

    Slide under the car near the back of the front wheels. The catalytic converter attaches to the head pipe near the rear of the engine with four bolts and a mounting flange. Loosen the nuts on the four bolts with a socket and ratchet, but do not remove them yet.

    3

    Locate the exhaust clamp on the pipe at the rear of the catalytic converter where it joins the rear exhaust pipe. Remove the two nuts from the clamp, then remove the clamp from the pipe. Move to the front of the converter and remove the four mounting bolts that you loosened earlier, then lower the front of the converter away from the head pipe.

    4

    Pull the converter forward, sliding it out of the rear pipe. Lower it to the ground and remove it from under the car.

    5

    Position a new converter under the car and raise it until you can slide the rear fitting on the converter into the rear pipe. Slide it in far enough to allow you to raise the front flange to the flange on the head pipe.

    6

    Install a new brass gasket between the front flanges, then install the four mounting bolts and nuts. Tighten the bolts with a socket and ratchet on one side and a wrench on the other. Install a new exhaust clamp on the rear pipe and tighten the nuts to secure it. Do not over-tighten it, or you will crush the exhaust pipe.

    7

    Move out from under the car and raise it off the jack stands with a jack. Remove the jack stands then set the car on its wheels. Remove the jack from under the car.

Read More.. >

Monday, April 14, 2014

1993 S10 Starter Removal

The removal of a 1993 S10 starter requires you to be under the Chevy truck so you can easily reach the components needed to remove it from the vehicle. Although the starter is located on the bell housing of the S10, the process for actually removing it is not overly difficult because you can reach it without removing unnecessary components.

Instructions

    1

    Place the front of the vehicle on jack stands and secure it by placing a wheel chuck behind the rear tire.

    2

    Open the engine hood and disconnect the negative battery cable. Leave the engine hood open to allow additional light to get under the S10.

    3

    Locate the starter next to the bell housing on the bottom drivers side of the engine. Use the replacement starter as a visual aid.

    4

    Remove the starter wire that bolts onto the back of the starter by removing the nut that secures the wire to the starter with a socket and ratchet.

    5

    Remove the three bolts that secure the starter to the bell housing with a socket and ratchet and then pull the starter gear free from the bell housing.

    6

    Disconnect the wiring connector that connects the starter solenoid to the electrical system. Push in on the center tap on the connector and pull on it to release it from the solenoid.

    7

    Connect the wiring connector to the solenoid on the replacement starter.

    8

    Place the gear of the starter into the bell housing and bolt the starter into place.

    9

    Reconnect the large starter wire and tighten it with the nut.

    10

    Reconnect the negative battery cable.

Read More.. >

Thursday, October 3, 2013

How to Replace the Oil Pump in a 1993 Ford Explorer

How to Replace the Oil Pump in a 1993 Ford Explorer

The oil pump in the 1993 Ford Explorer is a sump pump. This means the pump submerges into the oil in the oil pan and the pump pushes oil to the engine. This is a lot of work for a small pump. Over time, the pump weakens and the engine does not get the oil it needs to run properly. If this happens, you must replace the oil pump. Unfortunately, this task is labor intensive because you must remove the oil pan to get to the pump.

Instructions

    1

    Drive the Ford Explorer onto a set of ramps. Shut off the engine and set the parking brake for safety.

    2

    Open the engine hood and remove the oil filler cap and oil dipstick.

    3

    Place a drain pan under the oil pan drain plug and remove the plug using a socket and ratchet. Drain the oil into the drain pan and then insert the drain plug and tighten it.

    4

    Remove the bolts that secure the oil pan to the bottom of the engine block, using your socket and ratchet. Pry the pan free from the block using a metal scraper and then pull the pan out from under the Explorer.

    5

    Unplug the wiring harness connected to the oil pump.

    6

    Remove the jam nut that secures the oil pump to the oil pickup tube using an adjustable wrench. Turn the pump counterclockwise to remove it from the oil pickup tube.

    7

    Thread the new oil pump onto the oil pickup tube and tighten it using the jam nut and the adjustable wrench.

    8

    Plug the wiring harness back into the oil pump.

    9

    Scrape the old gasket material off the mating surfaces of the engine block and the oil pan. Wipe any old oil off the mating surfaces using a clean shop towel.

    10

    Place the gasket onto the mating surface of the oil pan, place the oil pan against the bottom of the engine block and, using the socket and ratchet, secure the pan to the block. Tighten the bolts in an alternating pattern from side to side.

    11

    Place a funnel into the oil filler spout and pour four quarts of oil into the engine.

    12

    Release the parking brake and drive the Ford off the ramps onto level ground. Shut off the engine and let it cool. Using the oil dipstick, check the oil level and add oil as needed. Replace the dipstick and filler cap.

Read More.. >

Sunday, September 15, 2013

How to Change the Timing Chain in a 1993 Toyota Pickup

The Toyota Pickup is a series of pickup trucks that Toyota has produced since 1968. The 1993 model belongs to the fifth generation of this series, which includes the 1988 through 1998 models. The standard engine for the 1993 Toyota Pickup is the 22-RE, a four-cylinder 2.4-liter engine with a single overhead camshaft. This engine uses a timing chain to synchronize the rotations of the crankshaft and camshaft.

Instructions

    1

    Disconnect the cylinder head from the engine with a socket wrench. Place a drain pan under the radiator drain, and remove the drain plug. Allow the coolant to drain from the radiator and replace the plug. Disconnect the radiator.

    2

    Remove the front differential from the engine with a socket wrench if your vehicle has all-wheel drive. Disconnect the oil pan, and detach the power steering belt if your vehicle has power steering. Remove the belt, compressor and bracket for the air conditioner if your vehicle is so equipped. Disconnect the cooling fan and its clutch. Remove the pulley for the water pump.

    3

    Install a counter-holding bar to the crankshaft pulley, and remove the mounting bolt for the crankshaft pulley with a socket wrench. Pull the pulley from its shaft with a pulley extractor. Disconnect the water bypass hose from the crankcase, and remove the adjusting bar for the fan belt. Detach the outlet pipe from the heater.

    4

    Remove the mounting bolts for the cover of the timing chain with a socket wrench, and discard the gaskets. Detach the timing chain from the sprocket of the crankshaft.

    5

    Detach the splines from the oil pump drive, and remove the sprocket for the crankshaft with a socket wrench. Wipe the cylinder block clean with a shop towel.

    6

    Rotate the crankshaft clockwise so the key on the crankshaft points straight up. Align the groove in the crankshaft sprocket with the key on the crankshaft, and slide the sprocket onto the crankshaft. Tighten the bolt for the crankshaft sprocket with a socket wrench.

    7

    Position the new timing chain on the camshaft sprocket so that the link between the two bright links on the timing chain aligns with the timing mark on the camshaft sprocket. Place the timing chain within its guides on the crankcase, and rotate the camshaft counterclockwise to remove the slack from the timing chain.

    8

    Install the drive for the oil pump over the key on the crankshaft. key. Place new gaskets onto the dowels of the timing chain cover, and install the timing chain cover. Tighten the 8mm mounting bolts to 9 ft. lbs. with a torque wrench. Tighten the 10mm mounting bolts to 29 ft. lbs.

    9

    Install the remaining components by performing steps one through three in reverse order. Tighten the bolt for the crankshaft pulley to 116 ft. lbs. with a torque wrench.

Read More.. >