Showing posts with label saturn. Show all posts
Showing posts with label saturn. Show all posts

Sunday, April 27, 2014

How to Replace the Catalytic Converter on a 1993 Saturn SL2

The catalytic converter on your Saturn SL2 bolts to a flange on the rear of the head pipe coming off the engine. A clogged converter can cause the engine to run very rough and will build up excessive amounts of heat under your car, which can radiate into the passenger compartment through the floorboards. While many people shy away from exhaust work, you can change the converter at home in the driveway and save yourself a potentially large repair bill.

Instructions

    1

    Position a jack under the front of your SL2 and raise the front end off the ground so you can work underneath it. Place a set of jack stands under the front suspension then lower the jack, allowing the car to settle onto the jack stands.

    2

    Slide under the car near the back of the front wheels. The catalytic converter attaches to the head pipe near the rear of the engine with four bolts and a mounting flange. Loosen the nuts on the four bolts with a socket and ratchet, but do not remove them yet.

    3

    Locate the exhaust clamp on the pipe at the rear of the catalytic converter where it joins the rear exhaust pipe. Remove the two nuts from the clamp, then remove the clamp from the pipe. Move to the front of the converter and remove the four mounting bolts that you loosened earlier, then lower the front of the converter away from the head pipe.

    4

    Pull the converter forward, sliding it out of the rear pipe. Lower it to the ground and remove it from under the car.

    5

    Position a new converter under the car and raise it until you can slide the rear fitting on the converter into the rear pipe. Slide it in far enough to allow you to raise the front flange to the flange on the head pipe.

    6

    Install a new brass gasket between the front flanges, then install the four mounting bolts and nuts. Tighten the bolts with a socket and ratchet on one side and a wrench on the other. Install a new exhaust clamp on the rear pipe and tighten the nuts to secure it. Do not over-tighten it, or you will crush the exhaust pipe.

    7

    Move out from under the car and raise it off the jack stands with a jack. Remove the jack stands then set the car on its wheels. Remove the jack from under the car.

Read More.. >

Monday, December 16, 2013

How to Replace a Starter on a 1999 Saturn

How to Replace a Starter on a 1999 Saturn

The starter in a 1998 Saturn mounts to the engine in the same location as most late model vehicles. It mounts below the engine, into the bell housing. In traditional fashion, the starter solenoid is bolted onto the starter to make it easier to remove both components at one time. When the starter fails to engage the flywheel, located inside of the bell housing, the engine does not start. When this happens, replace the starter to make your Saturn operable again.

Instructions

    1

    Disconnect the large black starter wire that connects to the starter. The wire secures to a threaded post on the starter with a small nut. The nut often rusts and removal is easiest with an adjustable wrench or vice grips.

    2

    Pull the wiring harness out of the Saturns starter solenoid by pushing on the small tab in the center and then by pulling on it.

    3

    Remove the three bolts that secure the starter to the Saturn. This requires a combination of a 12mm socket and a 12mm wrench. Use the socket on the two lower bolts and the wrench on the upper bolt. The use of a wrench accounts for clearance issues on the top bolt.

    4

    Pull the starter off the bell housing. Subsequently, this pulls the starter gear out of the bell housing where it meshes with the flywheel.

    5

    Place the new starter against the bell housing while you slide the gear into the bell housing. This meshes the gear with the flywheel.

    6

    Bolt the starter into place with the new bolts supplied with the starter. If new bolts were not supplied, use the old ones.

    7

    Slide the wiring harness onto the metal tab located on the starter solenoid until the harness snaps into place.

    8

    Reconnect the large black starter wire to the starter. Use the new nut threaded onto the replacement starter. Do not use the old nut.

Read More.. >

Saturday, November 16, 2013

How to Replace the Intake Manifold Gasket on a Saturn

The intake manifold gasket on your Saturn is a malleable material set in between the air intake manifold, the cylinder head and the engine block. The intake manifold gasket prevents air and fuel from leaking by sealing the gap between the cylinder head and the engine block. If your intake manifold is leaking, the car will experience a decrease in gas mileage and poor engine performance if the intake manifold gasket is leaking.

Instructions

    1

    Remove the air cleaner assembly. Remove the bolts holding the Saturns air cleaner in place, and remove the hose clamp screws holding the intake tubing to the throttle body. Pull the air cleaner assembly off the throttle body.

    2

    Disconnect the cable running to the negative battery terminal. Loosen the cable clamp nut and slide the cable off the negative terminal.

    3

    Label and disconnect all wires and hoses connected to the intake manifold with masking tape and a permanent marker. Note each wire and plugs location on the manifold.

    4

    Remove the bracket to manifold bolts. Unscrew the retaining nuts and the manifold to cylinder bolts and pull the intake manifold off.

    5

    Clean the old rubber gasket material off of the gasket mating surfaces with a razor blade, solvent and a clean rag.

    6

    Apply a bead of RTV sealant to the gasket mating surfaces on both the engine and the manifold.

    7

    Press the gasket onto the manifold. Make sure you have the gasket perfectly centered on the Saturns manifold.

    8

    Align the mounting holes on the intake manifold to the engine block and re-tighten all of the bolts you removed in step 5.

    9

    Reconnect all of the wiring and plugs to the intake manifold, and reconnect the battery.

    10

    Start the Saturns engine and check for any fuel leaking from the intake.

Read More.. >