Showing posts with label intake. Show all posts
Showing posts with label intake. Show all posts

Sunday, May 18, 2014

How to Remove the Lower Intake Manifold in a 1999 Ford 3 8

The standard engine in a 1999 Ford Mustang is a six-cylinder, 3.8-liter engine with fuel injection. The intake manifold on a car with fuel injection distributes the combustion mixture evenly to the cylinder head intakes, and is essential for optimizing the performance of the engine. The intake manifold in a 1999 Ford with a 3.8-liter engine has an upper and lower section, which you must remove separately.

Instructions

    1

    Place a clean, sealable container under the radiator drain and remove the drain plug with a socket wrench. Allow the coolant to drain into the container and seal the container for later use. Replace the drain plug.

    2

    Remove the filler cap on the fuel tank to relieve the pressure in the fuel tank. Connect fuel pressure gauge T80L-9974-B to the pressure relief valve on the fuel supply manifold. Place the tube of the fuel pressure gauge into a container approved for gasoline and open the valve on the pressure gauge. Drain the excess fuel into the container to relieve the pressure in the fuel system.

    3

    Disconnect the battery cable from the negative terminal with a socket wrench. Remove the intake air temperature sensor and the air intake tube. Detach the cables for the cruise control and accelerator. Disconnect the bracket for the accelerator.

    4

    Detach the electrical connectors for the exhaust gas recirculation and vacuum regulator solenoids, if your vehicle is so equipped. Disconnect the electrical wires to the spark plugs and the ignition coil. Disconnect any additional vacuum lines needed to access the lower intake manifold.

    5

    Disconnect the positive crankcase ventilation valve from the crankcase with a socket wrench. Detach the electrical connector for the throttle position sensor and idle air control valve. Remove the exhaust gas recirculation valve. Disconnect the bracket for the wiring harness of the engine control sensor and push it out of your way.

    6

    Remove the upper intake manifold with a socket wrench. Detach the fuel lines from the fuel supply manifold and disconnect the electrical connector for the engine coolant temperature sensor. Remove the fuel supply manifold and fuel injectors from the lower intake manifold as an assembly.

    7

    Disconnect the upper radiator hose and heater hose from the radiator. Remove the lower intake manifold from the engine with a socket wrench.

Read More.. >

Saturday, November 16, 2013

How to Replace the Intake Manifold Gasket on a Saturn

The intake manifold gasket on your Saturn is a malleable material set in between the air intake manifold, the cylinder head and the engine block. The intake manifold gasket prevents air and fuel from leaking by sealing the gap between the cylinder head and the engine block. If your intake manifold is leaking, the car will experience a decrease in gas mileage and poor engine performance if the intake manifold gasket is leaking.

Instructions

    1

    Remove the air cleaner assembly. Remove the bolts holding the Saturns air cleaner in place, and remove the hose clamp screws holding the intake tubing to the throttle body. Pull the air cleaner assembly off the throttle body.

    2

    Disconnect the cable running to the negative battery terminal. Loosen the cable clamp nut and slide the cable off the negative terminal.

    3

    Label and disconnect all wires and hoses connected to the intake manifold with masking tape and a permanent marker. Note each wire and plugs location on the manifold.

    4

    Remove the bracket to manifold bolts. Unscrew the retaining nuts and the manifold to cylinder bolts and pull the intake manifold off.

    5

    Clean the old rubber gasket material off of the gasket mating surfaces with a razor blade, solvent and a clean rag.

    6

    Apply a bead of RTV sealant to the gasket mating surfaces on both the engine and the manifold.

    7

    Press the gasket onto the manifold. Make sure you have the gasket perfectly centered on the Saturns manifold.

    8

    Align the mounting holes on the intake manifold to the engine block and re-tighten all of the bolts you removed in step 5.

    9

    Reconnect all of the wiring and plugs to the intake manifold, and reconnect the battery.

    10

    Start the Saturns engine and check for any fuel leaking from the intake.

Read More.. >