Friday, April 25, 2014
Engine Head Gasket Leak
A head gasket leak is the failure of the head gasket, a seal between the engine block, which houses the engines cylinders and pistons, and the cylinder head, which contains the valves that admit air and fuel into the cylinders.
Causes
Engine overheating is one of the most common causes of a head gasket leak; overheating makes the metal of the engine block expand and put so much pressure on the gasket that it no longer seals properly once the metal cools and contracts. Another common cause of a head gasket leak is engine misfiring. If combustion occurs too early or late, it can stress the head gasket.
Effects
If the head gasket starts to leak, the engine may blow blue smoke when oil reaches the combustion chamber or steam may come from the exhaust pipe if the chamber is contaminated with coolant. Fluid contamination, as well as increased risk of further engine overheating, can cause serious engine damage.
Repair
Replacing a head gasket is labor intensive because it is under the cylinder head, which is attached to many engine components, which may include the air intake, exhaust manifold and transmission housing.
Saturday, March 29, 2014
How to Change a Head Gasket on a Dodge Shadow 2 5 Liter Engine
The Dodge Shadow was a compact car that Chrysler produced from 1987 to 1994. It had a variety of engine options, including a four-cylinder 2.5-liter Premier engine. This engine uses a single cylinder head, and you must replace the gasket each time you remove the cylinder head. The procedure for changing the cylinder head gasket is generally the same for all versions of the Dodge Shadow with a 2.5-liter Premier engine.
Instructions
- 1
Open the fuel filler cap to relieve the pressure in the fuel tank. Disconnect the wiring harness for the fuel injectors from the throttle body. Attach a jumper wire from the first terminal of the harness to a ground point on the engine.
2Attach one end of another jumper wire to the second terminal of the harness. Touch the other end of the jumper wire to the positive terminal of the battery positive post for five seconds to relieve the pressure in the fuel system. Disconnect the jumper wires, and disconnect the cable from the negative battery terminal with a socket wrench.
3Remove the radiator cap, and start the engine. Turn the heater on, and allow the engine to idle until the upper radiator hose gets hot. Stop the engine, and place a container under the radiator drain cock on the bottom of the radiator. Open the drain cock with a socket wrench, and drain the coolant into the container. Fasten the drain cock.
4Detach the accessory drive belt from its pulleys. Disconnect the mounting bolts for the air compressor with a socket wrench, and push the compressor aside to obtain access to the cylinder heads. Secure the compressor in place with cord.
5Disconnect the upper radiator hose and heater hoses from the engine. Remove the cover for the rocker arms, and disconnect the mounting bolts for the rocker arm with a socket wrench. Pull the rocker arms and push rods from the engine block. Disconnect the intake manifold and exhaust manifold from the engine block.
6Remove the mounting bolts for the cylinder head with a socket wrench. Lift the cylinder head from the engine block, and remove the cylinder head gasket. Remove any traces of the old gasket from the cylinder head and engine block with a gasket scraper.
7Cut the heads off two of the cylinder head mounting bolts, and cut slots in one end of each bolt to serve as alignment dowels. Install the alignment dowels into the number 8 and number 10 mounting bolt holes. Place the new gasket for the cylinder head onto the alignment dowels with the numbers on the gasket facing up.
8Place the cylinder head on the engine block and install the mounting bolts. Tighten the head bolts to 22 foot-pounds with a torque wrench on the first pass, then tighten them to 45 foot-pounds on the second pass. Tighten bolts 1 through 6 to 110 foot-pounds, tighten bolt 7 to 100 foot-pounds and tighten bolts 8 through 10 to 110 foot-pounds.
9Install the rocker arms and push rods to their original position on the engine block. Install a new gasket for the rocker arm cover, and replace the cover. Attach the hoses to the engine, and fasten the mounting bolts for the air compressor. Tighten the mounting bolts to 20 foot-pounds with a torque wrench.
10Mount the accessory drive belt to its pulleys, and adjust the tension on the belt. Attach the cable for the negative terminal with a socket wrench, and fill the radiator with coolant. Start the engine and check for fluid leaks.
Sunday, January 19, 2014
How to Change the Exhaust Manifold Gasket in a F150 4 6L Engine
The Ford F150s history spans back to the 1948 Ford F-1 half-ton pickup. In 1975, the F-150 was released as a bridge between the F-100 and F-250. The F-150 replaced the F-100 as the smallest of the F-series pickups in 1984. In 1997, Ford dropped the 5.0-liter engine and replaced it with the 4.6-liter V-8, which remained until the 2010 model year. The exhaust manifold gasket is the gasket that seals the connection between the exhaust manifold and the engine. When this gasket fails, it not only creates an exhaust leak, but it can also create a poor running condition.
Instructions
- 1
Loosen and remove the the EGR valve tube, only on the left exhaust manifold, with a combination wrench. Trace the oil dipstick tube downward and locate the point where its bracket bolts to the engine block. Loosen the bolt securing the bracket to the block, with a ratchet and socket, and pull the tube and dipstick from the engine.
2Remove the nuts securing the exhaust manifold to the engine, using a ratchet and socket. If the nuts are frozen, apply a coat of rust penetrating spray to free them. Pry the manifold from the engine, using a 12-inch pry bar. Secure the manifold away from the engine using a bungee strap.
3Pull the old manifold gaskets from the 4.6-liter. Use a wire brush to clean the gasket mating surface on both the exhaust manifold and the engine.
4Place the new gaskets on the manifold studs protruding from the engine block. Each side of the 4.6-liter has two gaskets, one front and one rear.
5Release the exhaust manifold from the bungee strap and place it on the studs protruding from the engine block. Hand-tighten all of the nuts to secure the manifold in place.
6Tighten the nuts, in a crossing pattern starting from the upper rear bolt, to 13 to 16 foot-pounds of torque, using a torque wrench and a socket.
7Place the dipstick tube back into the engine and tighten the bracket bolt with a ratchet and socket.
8Reconnect the EGR valve tube to the exhaust manifold, if applicable, and tighten it to 26 to 33 foot-pounds with a torque wrench and combination wrench.
Saturday, December 21, 2013
Volvo 960 Liquid Gasket Removal
The valve cover on the Volvo 960 is finely machined and does not use a solid gasket as with most vehicles. Volvo instead requires the use of a liquid gasket. When you do any work requiring removal of the valve cover, a new liquid gasket should be applied. This necessitates removal of the old gasket. The process is tedious, but not difficult.
Instructions
- 1
Read the instructions for using the liquid gasket remover. Open the valve cover and expose the two surfaces where the liquid gasket was applied. Apply the gasket remover liberally on both surfaces and allow them to soak for approximately 10 minutes.
2Using the razor blade, carefully scrape the surfaces to remove the old gasket. Employ the putty knife in places where the razor blade wont fit. Continue to scrape, until all of the old gasket is gone. Wipe the surfaces clean with the shop cloth.
3Apply the gasket remover to both surfaces a second time and allow them to soak. Scrape the surfaces gently with either the razor blade or the putty knife and ensure that the entire surface has been cleaned of the old gasket. Wipe both surfaces with a shop cloth.
Sunday, December 1, 2013
What Is a Cylinder Head Gasket Leak Test
A head gasket creates the seal between the engine block and head. A cylinder head gasket leak test is a method of determining if the head gasket has failed without removing the head and visually inspecting the gasket.
Method
A cylinder leakage tester and air compressor are required to perform a cylinder leak test. A threaded insert is attached to the spark plug hole and an air gauge, then air is pumped via the compressor into the cylinde. A cylinder leak is determined by monitoring the gauge for pressure loss.
Locating the Leak
There may be various causes for a cylinder pressure leak. During the test, listen and feel for the escaping air to determine the source. Air gurgling through the radiator is the typical sign of head gasket failure. However, a cracked head may also cause air leaks into the radiator.
Alternatives
In addition to the cylinder leak test, there are other methods of testing for a defective head gasket. The cooling system can be pressure checked using a cooling system pressure tester. A block checker is another device that can test the head gasket. The block checker reacts to exhaust gases in the cooling system which indicates a leak.
Saturday, November 30, 2013
How to Change the Exhaust Manifold Gasket in a 2002 GMC Envoy
The exhaust manifold is the area of the vehicle where exhaust gases from the cylinders accumulate prior to being passed into the exhaust pipe. A poor manifold gasket, which is located between the manifold and engine cylinder, can lead to an exhaust leak, indicated by a ticking or tapping noise that is much louder when the engine is cold. As the engine warms up, the noise will dissipate. The procedure will vary slightly depending upon whether your 2002 Envoy is a V6 or V8 engine but, independent of the engine, the repair can be completed with the engine in place.
Instructions
- 1
Disconnect the cable from the batterys negative terminal. Lift the vehicle and support it securely on jack stands.
2Apply penetrating oil to the exhaust pipe-to-manifold studs and nuts from beneath the vehicle. The bolts are typically rusty. Wait a little while to allow the penetrating oil soak into the bolts.
3Remove the nuts retaining the exhaust pipe to the manifold, using a socket wrench. On a V8 engine, there will be two exhaust manifolds which are more easily accessed with the front tires and the inner fenderwalls removed, although it is not absolutely necessary.
4For a V6 Envoy, unplug the oxygen sensor electrical connector. On a V8 Envoy, detach the spark plug wires and remove the spark plugs from the manifold side being worked on. If both manifolds are being removed, detach all spark plug wires and remove all spark plugs.
5Remove the three heat shield nuts using a socket wrench then remove the heat shield. Place the heat shield aside.
6Perform the following if you are working on a V8 Envoy. The procedure is dependent upon the side of the vehicle where the manifold is located. For the right side, remove the air cleaner assembly and the oil dipstick. Unbolt the dip stick tube bracket and move the dipstick tube. Remove the EGR valve by removing the pipe to intake manifold mounting bolts, the EGR valve mounting bracket-to-cylinder head bolts and the EGR pipe-to-exhaust manifold mounting bolts. On the left side of the vehicle, simply disconnect the electrical connector from the engine coolant temperature sensor, which is at the front of the cylinder head above the number one spark plug.
7Remove the exhaust system manifold bolts using an open-ended wrench. Detach the manifold from the cylinder head. Remove the exhaust manifold gasket.
8Clean the mating surfaces on the cylinder head and the manifold using a gasket scraper to remove all carbon deposits. Check the manifold for cracks and make sure the bolt threads are clean and undamaged.
9Install a new gasket to the mating surfaces between the cylinder head and the manifold.
10Install the manifold on the cylinder head. Apply heat-resistant thread locking compound to the bolt threads and then start tightening the bolts by hand. Tighten the bolts with a torque wrench in three passes, starting from the center bolt and working your way to the ends. Tighten the bolts to 18 foot-lbs.
11Reinstall the remaining components in the reverse of removal, tightening the heat shield to 80 inch-lbs. using a torque wrench. Start the engine and check for exhaust leaks.
Friday, November 29, 2013
How to Replace the Head Gasket on a 1984 Ranger
The Ford Ranger is a compact pickup truck that has been in production since 1983, with the first generation of this series including the 1983 through 1988 models. The most common engines on the 1984 Ford Ranger are four-cylinder engines with a displacement of either 2.0 liters and 2.3 liters. These engines have a single cylinder head for all four cylinders, which sits on top of the engine block. The cylinder head gasket in the 1984 Ranger typically requires replacement when you remove the cylinder head.
Instructions
- 1
Remove the cable from the negative battery terminal with a socket wrench to prevent the engine from starting while replacing the cylinder head gasket. Place a container under the drain cock on the bottom of the radiator, and remove the drain cock with a socket wrench. Drain the coolant from the radiator into the container, and replace the drain cock.
2Disconnect the air cleaner from the intake manifold with a socket wrench, and remove the valve cover. Detach the drive belt for the air compressor if your vehicle is so equipped. Remove the mounting bolts for the air compressor, and remove the air compressor mounting bracket from the cylinder head. Push the air compressor out of the way to access the cylinder head.
3Remove the intake manifold and exhaust manifold from the cylinder head with a socket wrench. Record the position of the attaching screws on the cover for the cam shaft drive belt, so you can install the screws in the correct position later. Remove the cover for the cam shaft drive belt.
4Turn the tensioner for the drive belt counterclockwise with a socket wrench to relieve the tension on the drive belt. Detach the drive belt from its pulleys. Disconnect the water outlet and its hose from the cylinder head.
5Remove the water outlet elbow from the cylinder head with the hose still attached. Remove the mounting bolts from the cylinder head with a socket wrench, and lift the cylinder head from the cylinder block.
6Remove the gasket from the cylinder block. Clean the remaining gasket material and other debris from the cylinder head and cylinder block with a gasket scraper.
7Place the new gasket onto the cylinder block, and mount the cylinder head to the cylinder block. Tighten the mounting bolts for the cylinder head to between 50 and 52 foot-pounds with a torque wrench on the first pass. Tighten the mounting bolts to between 80 and 90 foot-pounds on the second pass.
8Mount the camshaft drive belt to its pulleys. Replace the cover for the camshaft drive and install the attaching bolts for the cover, using your notes from step three as a guide. Tighten the mounting bolts to between 6 and 13 foot-pounds with a torque wrench.
9Install a new gasket for the water outlet and connect the outlet to the engine. Tighten the mounting bolts to between 12 and 15 foot-pounds with a torque wrench. Install the exhaust manifold and intake manifold with a socket wrench. Fasten the mounting bracket for the air compressor to the cylinder head, if your vehicle is so equipped.
10Fill the vehicle with coolant, and connect the cable to the negative battery terminal with a socket wrench.
Saturday, November 16, 2013
How to Replace the Intake Manifold Gasket on a Saturn
The intake manifold gasket on your Saturn is a malleable material set in between the air intake manifold, the cylinder head and the engine block. The intake manifold gasket prevents air and fuel from leaking by sealing the gap between the cylinder head and the engine block. If your intake manifold is leaking, the car will experience a decrease in gas mileage and poor engine performance if the intake manifold gasket is leaking.
Instructions
- 1
Remove the air cleaner assembly. Remove the bolts holding the Saturns air cleaner in place, and remove the hose clamp screws holding the intake tubing to the throttle body. Pull the air cleaner assembly off the throttle body.
2Disconnect the cable running to the negative battery terminal. Loosen the cable clamp nut and slide the cable off the negative terminal.
3Label and disconnect all wires and hoses connected to the intake manifold with masking tape and a permanent marker. Note each wire and plugs location on the manifold.
4Remove the bracket to manifold bolts. Unscrew the retaining nuts and the manifold to cylinder bolts and pull the intake manifold off.
5Clean the old rubber gasket material off of the gasket mating surfaces with a razor blade, solvent and a clean rag.
6Apply a bead of RTV sealant to the gasket mating surfaces on both the engine and the manifold.
7Press the gasket onto the manifold. Make sure you have the gasket perfectly centered on the Saturns manifold.
8Align the mounting holes on the intake manifold to the engine block and re-tighten all of the bolts you removed in step 5.
9Reconnect all of the wiring and plugs to the intake manifold, and reconnect the battery.
10Start the Saturns engine and check for any fuel leaking from the intake.
Wednesday, October 2, 2013
What Happens if the Oil Pan Gasket Goes
An oil pan gasket is a flexible gasket that seals the oil pan to prevent oil from leaking. Oil pan gaskets rarely fail, but damage can occur to the oil pan, which may cause the gasket to leak.
Gasket Failure
When an oil pan gasket fails, oil will begin to leak from the oil pan. Car owners may notice oil spots in places where the car was parked. The most serious problem caused by a leaking oil pan gasket is the loss of oil.
Determining Leak Location
Oil may leak from a number of areas on an automobile. When oil leaks, it will run down the motor and may appear to be leaking from the oil pan. Before replacing the oil pan gasket, car owners should clean the engine and oil pan to determine the actual source of the leak.
Gasket Replacement
Replacing an oil pan gasket is not difficult, but it is messy. The oil should be drained from the car before replacing the gasket, but some oil will still remain in the pan and will drip from the engine. A model-specific repair manual is a useful resource for determining the steps to remove the oil pan.
Tuesday, September 17, 2013
How to Install a 98 Ford F150 4 6 Head Gasket
The Ford F150 is a 1/2-ton pickup truck that has been in continuous production since 1975. The 1998 model belongs the tenth generation of this series, which includes F150s made from 1997 to 2004. A 4.6-liter V-8 engine is one of the options available for the Ford F150. Each side of the engine has a cylinder head that covers the four cylinders on that side. The cylinder head gasket lies between the engine block and the cylinder head.
Instructions
- 1
Discharge the air conditioning system with a refrigerant recovery machine, if your vehicle is equipped with AC. This step requires a mechanic certified by the Environmental Protection Agency.
2Remove the cable from the negative battery terminal with a socket wrench. Disconnect the valve covers, and remove the intake manifold from the engine block. Detach the timing chains from the crankshaft sprocket and camshaft sprocket. Disconnect both exhaust manifolds from the engine block. Disconnect the air compressor to obtain access to the cylinder heads if your vehicle has air conditioning.
3Disconnect the retaining bolts from the heater hose with a socket wrench. Squeeze the hose clamp and pull it down the hose to release the clamp. Detach the heater hose from the cylinder head. Disconnect the mounting bolts from the cylinder head and pull the cylinder head from the engine block. Discard the gasket for the cylinder head and remove any remaining gasket material from the engine block with a gasket scraper.
4Turn the crankshaft clockwise until the key way on the crankshaft points straight up, and clean the cylinder head with a shop rag. Place the the new gasket for the cylinder head gasket over the dowel pins on the engine block, then mount the cylinder head on the engine block.
5Fasten new mounting bolts to the cylinder head by hand. Tighten the mounting bolts to between 27 and 31 foot-pounds on the first pass with a torque wrench. Tighten the bolts another 85 to 95 degrees with a socket wrench on the second pass. Tighten the bolts another 85 to 95 degrees on the third pass.
6Connect the heater hose to the cylinder head, and attach the hose clamp. Fasten the retaining bolts for the heater hose with a socket wrench. Connect the exhaust manifolds to the engine block, and mount the timing chain to the crankshaft sprocket and camshaft sprocket. Connect the intake manifold, and replace the valve covers.
7Attach the cable for the negative battery terminal with a socket wrench. Start the engine and check for coolant leaks. Recharge the air conditioning system, if your vehicle is so equipped. This requires a mechanic certified by the EPA.