Showing posts with label 98. Show all posts
Showing posts with label 98. Show all posts

Monday, December 2, 2013

How to Replace the ABS Module on a 98 Chevy Z71

The fourth generation of the Chevrolet C/K series of full-size pickup trucks was in production from 1987 to 1998. The Z71 off-road package for these vehicles included skid plates and improved shock absorbers. The anti-lock braking system, or ABS, for the 1998 Chevrolet C/K series required a module to control the braking power to each wheel during an emergency stop. The Z71 package did not affect the procedure for replacing the ABS module.

Instructions

    1

    Record the position of the electrical connectors and brake lines on the ABS module so you can attach them correctly later. The ABS module is in the engine compartment on the left side of the engine. It is a small box-like component that has brake lines connected to it.

    2

    Detach the electrical connectors from the ABS module. Remove the retaining bolts from the brake lines with a socket wrench, and disconnect the brake lines from the ABS module.

    3

    Disconnect the bolts from the ABS mounting module bracket with a socket wrench. Detach the bracket from the vehicle with the ABS module still attached. Remove the retaining bolts from the ABS module, and separate the ABS module from its mounting bracket.

    4

    Mount the new ABS module to its mounting bracket, and tighten the bolts to 5 foot-pounds with a torque wrench. Connect the bracket to the vehicle, and tighten its mounting bolts to 33 foot-pounds.

    5

    Attach the brake lines to their original fittings, and tighten the fittings to 16 foot-pounds with a torque wrench. Attach the electrical connectors to their original positions on the ABS module.

    6

    Bleed the ABS braking system, then bleed the regular braking system.

Read More.. >

Tuesday, September 17, 2013

How to Install a 98 Ford F150 4 6 Head Gasket

The Ford F150 is a 1/2-ton pickup truck that has been in continuous production since 1975. The 1998 model belongs the tenth generation of this series, which includes F150s made from 1997 to 2004. A 4.6-liter V-8 engine is one of the options available for the Ford F150. Each side of the engine has a cylinder head that covers the four cylinders on that side. The cylinder head gasket lies between the engine block and the cylinder head.

Instructions

    1

    Discharge the air conditioning system with a refrigerant recovery machine, if your vehicle is equipped with AC. This step requires a mechanic certified by the Environmental Protection Agency.

    2

    Remove the cable from the negative battery terminal with a socket wrench. Disconnect the valve covers, and remove the intake manifold from the engine block. Detach the timing chains from the crankshaft sprocket and camshaft sprocket. Disconnect both exhaust manifolds from the engine block. Disconnect the air compressor to obtain access to the cylinder heads if your vehicle has air conditioning.

    3

    Disconnect the retaining bolts from the heater hose with a socket wrench. Squeeze the hose clamp and pull it down the hose to release the clamp. Detach the heater hose from the cylinder head. Disconnect the mounting bolts from the cylinder head and pull the cylinder head from the engine block. Discard the gasket for the cylinder head and remove any remaining gasket material from the engine block with a gasket scraper.

    4

    Turn the crankshaft clockwise until the key way on the crankshaft points straight up, and clean the cylinder head with a shop rag. Place the the new gasket for the cylinder head gasket over the dowel pins on the engine block, then mount the cylinder head on the engine block.

    5

    Fasten new mounting bolts to the cylinder head by hand. Tighten the mounting bolts to between 27 and 31 foot-pounds on the first pass with a torque wrench. Tighten the bolts another 85 to 95 degrees with a socket wrench on the second pass. Tighten the bolts another 85 to 95 degrees on the third pass.

    6

    Connect the heater hose to the cylinder head, and attach the hose clamp. Fasten the retaining bolts for the heater hose with a socket wrench. Connect the exhaust manifolds to the engine block, and mount the timing chain to the crankshaft sprocket and camshaft sprocket. Connect the intake manifold, and replace the valve covers.

    7

    Attach the cable for the negative battery terminal with a socket wrench. Start the engine and check for coolant leaks. Recharge the air conditioning system, if your vehicle is so equipped. This requires a mechanic certified by the EPA.

Read More.. >