Showing posts with label troubleshooting. Show all posts
Showing posts with label troubleshooting. Show all posts

Sunday, March 9, 2014

Troubleshooting a Mazda MPV

Troubleshooting a Mazda MPV

Mazdas MPV is a sedan-style car that is perred by consumers for its fuel economy. If you are having problems with your Mazda MPV, there are several things that you can do before you take it to a service shop. Dead batteries, no gas, or a low coolant level can lead to the Mazda MPV not starting. You dont have to be a Mazda technician to get your MPV back on the road. You can generally do it yourself with little hassle.

Instructions

    1

    Turn the key in the MPVs ignition and look over the instrument panel. Check the fuel level and the battery charge to determine if this is your problem. If you hear a clicking noise when your turn the key, you need to have your alternator replaced by a service technician.

    2

    Fill the gas tank with gasoline if needed. Pop the hood to your Mazda MPV and look over the battery connections. The battery is located on the right side of the engine. The battery should be properly connected to the terminals. Use a pair of channel locks to tighten the cable connections to the battery terminals.

    3

    Use a voltmeter to test the battery charge. Hold the leads of the voltmeter to the terminals on the top of the battery. You should get a 12V reading. If you dont get a 12V reading, you can jump the battery.

    4

    Have a friend hook jumper-cables up to their car battery and then connect the other ends of the jumper cable to your cars battery. Start the other car and then try to start your MPV. Allow the battery to charge for about 10 minutes before you turn the MPV off. Try to restart the MPV. If the MPV doesnt restart, the battery is dead and you will need to replace it.

    5

    Check over the coolant system if your MPV is overheating. Locate the coolant tank on the left side of the engine. Look for the fill line on the edge of the tank. Make sure that you coolant is filled to the fill line. If the coolant is not filled to that line, fill it with 50/50 coolant.

Read More.. >

Monday, December 16, 2013

Ford Explorer Transfer Case Troubleshooting

Ford Explorer Transfer Case Troubleshooting

The Ford Explorer was first manufactured in 1991 and is still in production as of 2011. The transfer case conveys power from the transmission to the axles and can be changed from two-wheel drive to four-wheel drive. Problems with this part makes the vehicle virtually unusable. Several issues can be averted with the careful application of preventative maintenance, but when trouble starts you can at least diagnose the most likely reason for the difficulty.

Instructions

    1
    Check the transfer case while the vehicle is in motion.
    Check the transfer case while the vehicle is in motion.

    Drive the vehicle slowly and attempt to engage the four wheel drive through all gears: "2H", "4H", "N", and "4L". Noisiness, jumping out of gear or difficulty shifting indicates further inspection and testing is needed.

    2
    Proper preparation makes checking the transfer case much easier.
    Proper preparation makes checking the transfer case much easier.

    Place the vehicle on a hard level surface and set the parking brake. Engage the drive through all gears with the Explorer stationary. The shifter should work smoothly through all four settings. Difficulty shifting and noisiness requires investigation of the components. The linkage might be loose, bent or binding in movement. Any of the parts in the transfer case may be worn or damaged. These all indicate further troubleshooting is needed.

    3
    When working underneath a vehicle be sure to use jackstands.
    When working underneath a vehicle be sure to use jackstands.

    Jack up the vehicle and place it jack stands. The transfer case is located between the transmission and the rear axle. Check for any leaks or fluid in or around the transfer case, but particularly around the front and rear shafts because they both have seals that can be worn. Locate the transfer case fill plug. It is behind the transfer case damper if installed. If so, remove the damper. Remove the plug and insert your little finger to measure. The lubricant should be at or just below the bottom edge of the plug hole.

    4
    Problems with the transfer case can extend to other parts of the vehicle.
    Problems with the transfer case can extend to other parts of the vehicle.

    Remove the transfer case to ensure the components inside are not damaged or misaligned. Where equipped, remove the skid plate. If the damper is still in place, remove it. Drain the lubricant by removing the drain plug on the bottom of the transfer case. Remove the electrical connector, if installed, then remove the speed sensor and speedometer cable from the case. Disconnect both drive shafts. Remove the mounting bracket for the electrical connector, or the vent hose from the shift lever on manual models. For manual models, remove the nut from the shift lever and remove it and the bolts holding the shifter to the extension housing.

    5

    Place a transmission jack under the transfer case and lift it slightly so that you can use safety chains to attach the case to the jack. Remove the five bolts holding the case, and slide the case down and away from the vehicle. Remove and discard the gasket between the case and the extension housing. Inspect all parts for wear, breakage, misplacement or misalignment. Any parts with those signs must be replaced before reinstalling the transfer case.

Read More.. >

Thursday, November 28, 2013

86 Mustang Troubleshooting

86 Mustang Troubleshooting

The 1986 Ford Mustang is a fuel-injected, eight cylinder engine. It produces about 200 horsepower and is available with a four-speed automatic or five-speed manual transmission. Engines problems may occur with this older model Mustang that can keep the engine from properly starting and running.

Dead Battery

    Check the battery if the 1986 Mustang wont start. An easy way of determining whether or not the battery is dead is by trying to put on the lights or turn the radio on. If both are unresponsive and the car wont start, check the battery connections, try jumpstarting the vehicle or replacing the battery.

Fuel Filter

    Replace the fuel filter if the lights and radio are functioning but the vehicle still wont start. The fuel filter should be replaced every 50,000 miles. If not, the fuel filter can become clogged and prevent gas from entering fuel injectors.

Old/No Gas

    If the car has not been run in more than a year, the problem may be old gasoline in the tank. To test, try running the engine with ether. Put the ether into the throttle body and see if the engine starts and continues running. If the engine continues running, the problem is not with the gas in the tank. As simple as it sounds, be sure there is gas in the tank. If not, add fresh fuel and try again.

Read More.. >