Saturday, February 8, 2014
How to Mount Low Profile Auto Tires
Many cars today are designed with low-profile tires, which improve handling and support on the roads. Low-profile tires can prove difficult to install because their sidewalls sit so low to the ground. The sidewall doesnt offer much flexibility, which makes for a hard removal. You can change these low profile tires without much hassle using special equipment. Most newer rim clamp tire machines have the functionality to mount low-profile tires.
Instructions
- 1
Put on eye protection and gloves.
2Familiarize yourself with the rim clamp tire machine. You should find it quite self-explanatory because every functioning pedal and lever has arrows and labels. Notice that it has a plate with clamps where the wheel will sit and that it has a bead breaker on the side. The machine has an installation arm and an inflation hose to inflate tires to the correct level of lbs. per square inch (psi). The rim clamp machine also has a pressure arm designed to push the tire below the drop center to make it easy to install a low-profile tire.
3Lift the wheel up onto the plate, and press the pedal that locks the clamps to the wheel. Lift up your tire, and look at both of its sides. You will notice a directional arrow or a note if the tire has a side that should face outside. Look for instructions written on the sidewall of the tire.
4Push the first bead of the tire onto the rim with force in a rocking motion. You should be able to simply push the first bead on the wheel by hand.
5Swing the tire installation arm over, and position the tire between the head of the installer and at a slant onto the wheel. Press the pedal that will rotate the plate to move the tire onto the rim. Slide out the pressure arm, and use the lever to push the tire down and hold it under the drop center bead of the wheel while the plate turns and until youve installed the tire on the wheel.
6Inflate the tire with an inflation hose by pushing it on the valve stem and pressing the inflation pedal. Look at the tire to find the proper inflation, and fill it to that number. Check the psi with your tire pressure gauge.
7Press the pedal to release the clamps.
Sunday, January 12, 2014
What Happens If a Motor Mount Is Broken
A motor mount does more than simply hold a motor in place. A motor mount utilizes a rubber bushing to hold a cars engine, which helps to dampen vibration and movement that can cause damage to the engine and surrounding components.
Noise and Vibration
A broken motor mount will cause a significant increase in noise and vibration. As the motor moves within the broken mount, the engine often strikes the mount, creating a loud thump. The normal vibration of the motor that is dampened by the mount will often also be transferred to the entire vehicle, causing a noticeable shake.
Engine Component Damage
As the motor moves, damage may also occur to the flexible hoses and wiring that run to the motor. While these parts are designed for flexibility, the sudden and longer movements of a motor that is not properly secured can pull wires and hoses loose as well as weaken them. A broken motor mount may also cause exhaust leaks.
Motor Mount Damage
When a motor mount is broken, the motor is allowed to move more than intended. This causes additional stress to the other motor mounts, which will quickly wear and may break under the added strain.
Friday, December 27, 2013
How to Mount a Dash Pad
Sunlight and constant temperature changes cause dashboards to become brittle and crack. The cracks ruin the interior of your vehicle and allow the underlayment to become brittle. This leads to a fine dust covering the contents of the vehicle. Replacing a dashboard requires disassembling the dash, and a replacement dash can cost hundreds of dollars. Installing a dash pad requires less labor and costs less than a replacement dashboard.
Instructions
- 1
Wipe the dash pad with a clean rag. Shake the paint can thoroughly for 30 to 60 seconds. Spray multiple light coats of plastic spray paint onto the surface of the dash pad. Allow the paint to cure for 24 hours before proceeding with the installation.
2Set a tube of silicone adhesive into a bowl of hot water. Allow the silicone to soften while you prepare the dashboard for the dash pad.
3Cut protruding material from the cracked dashboard with a razor knife. Even out rough spots by sanding the dashboard with 100-grit sandpaper. Spray an ammonia-based window cleaner onto the sanded dashboard. Wipe the cleaner from the dash with a clean rag.
4Set the dash pad on top of the prepped dashboard. Trim the dash pad to fit the contours of the dashboard. Remove the dash pad from your vehicle.
5Remove the silicone adhesive from the hot water. Apply a bead of silicone remover to the underside edges of the dash pad. Apply additional adhesive to the surface of the dashboard.
6Press the dash pad onto the surface of the dashboard. Work from the center to the edges of the dash pad with a clean rag to spread the adhesive and remove wrinkles.
7Allow the adhesive to cure for 24 hours to ensure proper adhesion between the dash pad and the dashboard.
Friday, December 6, 2013
The Purpose of a Transmission Mount
A transmission mount provides support for the transmission. A transmission mount and a motor mount are essentially identical, but one supports the transmission and the other the engine. Both are often referred to as a motor mount.
Protecting Transmission
The primary purpose of a transmission mount is to hold the transmission in place and reduce its movements. A transmission that moves too much can cause damage, especially in the linkages between the transmission and the engine and drive shaft. Transmission movements can also damage lines and hoses running from or near the transmission.
Noise and Vibration
Another purpose of the transmission mount is to reduce the amount of noise and vibration in the vehicle. This is done to make the vehicle drive as smoothly and quietly as possible both for the comfort of the driver and passengers as well as to reduce wear on the vehicle body and suspension.
Design
Most transmission mounts are simple devices made of two metal plates and a block of rubber. One plate attaches to the transmission and the other to the vehicles body. The rubber block is held between the plates and dampens the transmissions movements. Some transmission mounts are hydraulic, using a hydraulic fluid in place of the rubber.
Thursday, November 21, 2013
How to Mount a Twin Cam on an Evo Hard Tail
Before you mount a Twin Cam engine on an Evoluation (Evo) hard tail, you must take into consideration the two types of Twin Cam engines. The Twin Cam 88B is balanced, and although it is theoretically possible to modify an Evo frame to accommodate a Twin Cam 88B, it is probably not worth the trouble. The Twin Cam 88A is not balanced and it is possible to mount this engine in an Evolution frame. It is irrelevant whether the frame is a bolt-on hard tail, weld-on hard tail, softail or swingarm frame. Zodiac Performance Products and Vulcan Engineering both sell motor mount adapter plates that are intended to facilitate the installation of a Twin Cam 88A in an Evo frame.
Instructions
- 1
Bolt the Zodiac adapter plate to the rear engine mount with a hex socket and socket wrench. Grind the frame mount flush with the front of the adapter plate if any part of the rear engine mount protrudes in front of the adapter plate using an angle grinder.
2Bolt the adapter plate to the engine with a hex socket and socket wrench. Mark the 3/8-inch wide cast gusset that is visible through the right side adapter plate window with a mechanics awl.
3Unbolt the adapter plate from the engine. Grind the marked area of the gusset flush with the engine case casting to create spanner clearance.
4Place, but do not bolt, the adapter plate on the rear engine mount. Align the two dowels included with the adapter plate in the engine bottom flange.
5Slide the engine into the frame. Lift the back of the engine onto the adapter plate.
6Bolt the adapter plate to the engine with the 3/8 by 2-inch Allen screws and washers included with the adapter plate using an Allen socket and socket wrench.
7Bolt the adapter plate to the rear motor mount with the 3/8 by 1 3/4-inch Allen screws and washers included with the adapter using a Allen socket and socket wrench.
8Wrench tighten the rear engine mount and adapter bolts to 38 foot-pounds of torque with an Allen socket and torque wrench after installing the stock, front engine mount.