Showing posts with label tail. Show all posts
Showing posts with label tail. Show all posts

Monday, February 17, 2014

How to Replace Jeep Liberty Tail Lights

The tail lights on the Jeep Liberty are enclosed in a plastic assembly with the bulbs mounted inside. To access the bulbs, you must first remove the assembly from the Jeep, but you can remove it in a few minutes with basic hand tools. The bulbs used in the tail light are standard 3057 bulbs, available at any auto parts store. These bulbs have a dual filament so they operate both the brake and tail lights.

Instructions

    1

    Open the lift gate of your Jeep and locate the retaining screws along the inner edge of the tail light assembly. Remove the screws with a socket and ratchet and set them aside.

    2

    Separate the tail light assembly from the rear of the Jeep and locate the electrical connector on the rear of the assembly. Depress the locking tab and pull the connector away from the tail light back plate.

    3

    Remove the two screws that hold the back plate to the tail light assembly with a Phillips head screwdriver then separate the back plate from the tail light. Grasp the bulb and pull it straight out of the back plate. Discard it.

    4

    Install a new 3057 bulb into the back plate, pushing it in until it seats firmly in the socket. Install the back plate on the rear of the tail light assembly then install the two retaining screws and tighten them with the Phillips head screwdriver.

    5

    Position the tail light assembly on the rear of the Jeep, install the retaining screws and tighten them with a socket and ratchet. Do not over-tighten these screws or you will crack the plastic assembly. Close the lift gate and test the light by turning on the head light switch.

Read More.. >

Tuesday, December 10, 2013

How to Replace Jeep Muffler Tail Pipe

How to Replace Jeep Muffler & Tail Pipe

If you take your Jeep Wrangler off road often, rust problems can develop on your exhaust system due to water and moisture. Whether you are replacing your exhaust with an aftermarket kit or a factory system, the process is virtually the same. Exhaust kits may be purchased at any local auto parts store and installed yourself using simple tools. Eye protection must be worn to protect against falling debris.

Instructions

Removal of Stock Exhaust

    1

    Cut the exhaust pipe directly behind the muffler using a hack saw.

    2

    Remove the bolts on the flange that connects the muffler to the catalytic converter using a ratchet and socket. Remove the muffler from the vehicle.

    3

    Remove the stock tailpipe hangers off the factory mounts located on the frame by pulling them out of the rubber bushings with your hands.

    4

    Pull the stock tailpipe out of the vehicle.

Installation of New Exhaust

    5

    Slide the tailpipe hangers into the stock bushings located on the frame.

    6

    Lift the muffler into position. Slide one end into the tailpipe.

    7

    Install the flange onto the catalytic converter and tighten the bolts using a ratchet and socket.

    8

    Place the exhaust clamp that came with the kit over the muffler and tailpipe connection. Tighten the bolts using a ratchet and socket.

    9

    Start the vehicle and check for leaks in the system.

Read More.. >

Thursday, November 21, 2013

How to Mount a Twin Cam on an Evo Hard Tail

How to Mount a Twin Cam on an Evo Hard Tail

Before you mount a Twin Cam engine on an Evoluation (Evo) hard tail, you must take into consideration the two types of Twin Cam engines. The Twin Cam 88B is balanced, and although it is theoretically possible to modify an Evo frame to accommodate a Twin Cam 88B, it is probably not worth the trouble. The Twin Cam 88A is not balanced and it is possible to mount this engine in an Evolution frame. It is irrelevant whether the frame is a bolt-on hard tail, weld-on hard tail, softail or swingarm frame. Zodiac Performance Products and Vulcan Engineering both sell motor mount adapter plates that are intended to facilitate the installation of a Twin Cam 88A in an Evo frame.

Instructions

    1

    Bolt the Zodiac adapter plate to the rear engine mount with a hex socket and socket wrench. Grind the frame mount flush with the front of the adapter plate if any part of the rear engine mount protrudes in front of the adapter plate using an angle grinder.

    2

    Bolt the adapter plate to the engine with a hex socket and socket wrench. Mark the 3/8-inch wide cast gusset that is visible through the right side adapter plate window with a mechanics awl.

    3

    Unbolt the adapter plate from the engine. Grind the marked area of the gusset flush with the engine case casting to create spanner clearance.

    4

    Place, but do not bolt, the adapter plate on the rear engine mount. Align the two dowels included with the adapter plate in the engine bottom flange.

    5

    Slide the engine into the frame. Lift the back of the engine onto the adapter plate.

    6

    Bolt the adapter plate to the engine with the 3/8 by 2-inch Allen screws and washers included with the adapter plate using an Allen socket and socket wrench.

    7

    Bolt the adapter plate to the rear motor mount with the 3/8 by 1 3/4-inch Allen screws and washers included with the adapter using a Allen socket and socket wrench.

    8

    Wrench tighten the rear engine mount and adapter bolts to 38 foot-pounds of torque with an Allen socket and torque wrench after installing the stock, front engine mount.

Read More.. >

Thursday, November 7, 2013

How to Replace the Tail Light Bulb on a 1998 Silverado

How to Replace the Tail Light Bulb on a 1998 Silverado

The taillight assembly on a 1998 Chevy Silverado houses the brake/taillight combination bulb, the reverse bulb and the turn-signal bulb. The brake/taillight combination bulb takes one type of bulb or another depending on when and where the 1998 Silverado was manufactured. Most 1998 Silverados use the 3057 automotive replacement bulb, but some use an 1157 replacement bulb. Getting to the bulbs requires a single procedure regardless of which bulb your 1998 Silverado uses, but there is a slight difference for extracting the different bulbs from their respective sockets.

Instructions

    1

    Ensure the headlight switch inside the passenger cab is in the off position.

    2

    Open the 1998 Chevy Silverados tailgate.

    3

    Locate the two retaining screws on the taillight assembly (the screws were revealed after you lowered the tailgate) that has the faulty taillight bulb. Remove the two screws with the Phillips screwdriver.

    4

    Turn the assembly around and rest it on the bumper with the wire harness still connected to the underside of the headlight assembly.

    5

    Grasp the taillight socket and twist it counterclockwise 1/3 turn to remove the bulb and socket from the taillight assembly.

    6

    Pull the 3057 replacement bulb straight out of the socket and push the new replacement bulb into the socket. For the 1157 bulb, remove the old one by pushing down on the bulb slightly while twisting the bulb 1/4 turn counterclockwise, then pulling the bulb from the socket. Align the dual notches on the base of the replacement bulb to the grooves inside the socket. Push the bulb slightly downward while twisting it clockwise to lock the bulb in the socket.

    7

    Align the notches on the external section of the socket with the matching grooves in back of the taillight assembly.

    8

    Reinstall the taillight assembly and replace the retaining screws. Close the tailgate.

Read More.. >