Tuesday, December 3, 2013
How to Replace the High Stoplight on a 2007 Hyundai Sonata
The high-mount stoplight or combination light assembly, as Hyundai calls it, on the rear of the 2007 Sonata uses a 921 bulb, which is a key part of the Sonatas rear lighting system. The light is designed to be highly visible to drivers behind you when the Sonatas brakes are applied and helps to avoid rear-end collisions. Removal of the Sonatas taillight assembly is required to replace the stoplight.
Instructions
- 1
Open the trunk of your Sonata and lay on your back inside the trunk looking up at the bottom of the package tray, or rear deck, directly below where the light assembly sits. Locate the two gold-colored Phillips head screws that retain the light assembly.
2Remove the two retaining screws using a long Phillips screwdriver then move to the inside of the car to access the light assembly on the top side of the rear deck, which is inside the passenger compartment. Lift the rear of the assembly slightly while pulling it forward to free it from the package tray. Turn the assembly over and locate the bulb socket on the underside.
3Rotate the bulb socket counterclockwise to unlock it, then pull it out of the taillight housing. Grasp the bulb, pull it straight out of the socket and discard it. Push a new 921 bulb into the socket; make sure it seats completely.
4Slide the bulb and socket into the taillight assembly then rotate the socket clockwise a quarter turn, locking it in place. Turn the taillight assembly over, slide the tabs on the bottom of the assembly in the holes in the package tray and slide the assembly forward until it sits flat on the tray.
5Move to the trunk and reinstall the two Phillips head screws with the long screwdriver. Tighten the screws until they are snug. Do not over-tighten these screws or you will crack the taillight assembly.
6Close the trunk and test the light; have someone step on the brake pedal or watch the light while you press the pedal. If the light functions properly, the repair is successful.
Wednesday, October 23, 2013
How to Replace a 2003 Hyundai Sonata Timing Belt
The 2003 Hyundai Sonata is available with a four-cylinder 2.0-liter engine with a double overhead cam. This engine design requires a timing belt to synchronize the crankshaft with the camshaft. The Sonatas timing belt should be replaced approximately every 60,000 miles.
Instructions
- 1
Remove components as required to access the cover of the timing belt on the front of the engine. Disconnect the cover with a socket wrench. Turn the crankshaft clockwise to align the timing mark on the crankshaft sprocket with the timing mark on the cylinder head. This places the No. 1 piston in the top dead center position needed to replace the timing belt.
2Disconnect the tensioner and the idler pulley for the timing belt with a socket wrench. Detach the timing belt from the crankshaft and camshaft.
3Turn the crankshaft clockwise again to align the timing marks if necessary. Connect the tensioner for the timing belt and the idler pulley. Tighten the mounting bolt for the idler pulley to between 32 and 41 ft-lbs. with a torque wrench.
4Place the timing belt over the camshaft sprocket and crankshaft sprocket in that order. Turn the timing belt tensioner to place tension on the timing belt. The timing belt is at the proper tension when five pounds of force in the middle of the longest span of the timing belt produces a deflection of 0.16 to 0.24 in.
5Tighten the bolt for the tensioner pulley to between 32 and 41 ft-lbs. with a torque wrench. Turn the crankshaft sprocket clockwise by one complete turn to realign the timing marks.
6Adjust the belt tension again if necessary. Replace the cover of the timing belt cover and any components you removed to access the timing belt.
Friday, October 18, 2013
How Do I Replace a 2000 Hyundai Sonata GLS Oxygen Sensor
The oxygen sensors in the 2000 Hyundai Sonata GLS are threaded into the exhaust manifold and the exhaust pipe near the catalytic converter. When an oxygen sensor malfunctions, your car will burn a significant amount of additional fuel. To save the unnecessary fuel expense and possible long-term engine damage, you should replace the sensors as soon as possible. Buy sensors for your Sonata from an auto-parts store or Hyundai dealer.
Instructions
- 1
Raise the Sonata with a jack. Rest the car on jack stands for stability.
2Locate the oxygen sensor either on the manifold or near the catalytic converter, depending on which one you need to change. Pull the wiring connection apart. Remove the oxygen sensor using a wrench.
3Coat the threads of the sensor with anti-seize. Select an anti-seize compound designed for electrical components. Insert the new sensor by hand. Torque it to 40 foot-pounds with your torque wrench.
4Push the two ends of the wiring harness together. The connector will click when it is attached. Repeat the replacement process on the second oxygen sensor if necessary. Lift the car slightly and pull the jack stands out of place. Lower the car to the ground.