Sunday, April 20, 2014
How to Replace a Diesel Injection Pump in a 2003 Dodge
A diesel engine is an option for many Dodge vehicles, especially heavy trucks. An eight-cylinder 5.9-liter diesel engine is available for the 2003 Dodge Ram 2500 3/4 ton pickup. This engine uses fuel injection and requires an injection pump to keep the fuel under pressure. The procedure for replacing the diesel injection pump is the same for all full-size Dodge trucks made from 2001 to 2005.
Instructions
- 1
Disconnect the cables from the negative battery terminals with a socket wrench. Remove the throttle linkage and its bracket. Disconnect the fuel drain manifold, and detach the fuel lines from the injection pump. Remove the fuel air control tube and the connector for the fuel shut-off valve from the injection pump. Disconnect the support bracket and oil fill tube from the injector pump.
2Put a shop rag over the opening in the injector pumps gear cover. Remove the gear retaining nut and washer for the injector pump with a socket wrench. Turn the crankshaft clockwise with a socket wrench until the top dead center pin on the crankshaft drops into the gear timing hole. Pull the pin from the gear timing hole.
3Remove the lock screw and its washer from the injection pump with a socket wrench. Tighten the lock screw to 22 ft. lbs. with a torque wrench, then push the drive gear for the injection pump from the drive shaft. Disconnect the mounting nuts for the injection pump with a socket wrench. Remove the injection pump from the crankcase.
4Install the new injection pump and tighten the mounting nuts by hand, ensuring that the pump can move freely within its slots. Connect the drive gear to the drive shaft with its retaining nut and washer. Tighten the nut to between 11 and 15 ft. lbs. with a torque wrench.
5Rotate the injection pump counterclockwise to take up gear lash. Tighten its mounting nuts to 18 ft. lbs. with a torque wrench. Connect the support bracket for the injection pump. Tighten the nut for the pump drive gear to 48 ft. lbs.
6Connect the oil filler tube and connector valve for the fuel shut-off valve to the injector pump. Attach the fuel lines to the injector pump. Install the fuel drain manifold and throttle linkage with a socket wrench. Connect the cables for the negative battery terminals.
7Loosen the bleed bolt on the fuel rail with a socket wrench. Push the primer button on the fuel transfer pump until the fuel coming from the bleed screw no longer has air bubbles. Tighten the bleed screw to 72 in. lbs. with a torque wrench. Start the engine and check for fuel leaks.
Wednesday, November 13, 2013
How to Take the Cylinder Head Off a 7 3 Ford Diesel
International Harvester manufactured the 7.3-liter diesel engines that appear in Ford trucks from 1988 to 1992. This engine is most common in Ford trucks with a rated carrying capacity of at least 1/2 ton. The 7.3-liter Ford diesel engine uses a single cylinder head for all eight cylinders in the engine. The cylinder head is on top of the engine block and is part of the combustion chamber. The procedure for removing the cylinder head from a 7.3-liter engine is the same for all Ford trucks.
Instructions
- 1
Disconnect the cables from the negative terminals of both batteries with a socket wrench. This prevents anyone from starting the engine while removing the cylinder head.
2Put a drain pan under the radiator. Remove the drain plug with a socket wrench and allow the coolant in the radiator to drain into the pan. Store the coolant for later use.
3Detach the shrouds for the radiator fan with a socket wrench. Disconnect the fan and clutch for the radiator as an assembly by using tools T83T-6312-A and T83T-6312-B. The mounting nut for the radiator fan and clutch has a left-hand thread, so you must turn it clockwise to remove the nut.
4Label the electrical wiring on the alternator so you can connect it correctly later and detach the wiring from the alternator. Disconnect the bolts for the alternator and vacuum pump with a socket wrench. Remove these components from the engine block.
5Disconnect the coolant hose from the cylinder head with a socket wrench. Remove the fuel injection pump from the engine block. Disconnect the intake manifold and valley cover from the engine block.
6Raise the vehicle with a floor jack and support it with jack stands. Remove the exhaust pipes from the exhaust manifolds with a socket wrench. Disconnect the clamp and mounting bolt for the oil dipstick tube. Detach the oil dipstick tube from the cylinder head and lower the vehicle.
7Disconnect the valve covers with a socket wrench and remove the rocker arms from the engine block. Record the position of each push rod, so you can re-install them correctly later. Remove the push rods from the engine block.
8Remove the fuel injector nozzles and glow plugs from the engine block with a socket wrench. Disconnect the mounting bolts for the cylinder head with a socket wrench. Install lifting eyes on each end of the cylinder block with tool T70P-6000.
9Lift the cylinder head from the engine block with the lifting eyes. Use caution to prevent the pre-chambers of the cylinder head from falling onto the engine when you remove the cylinder head.
Monday, October 28, 2013
Cummins 3 9 Turbo Diesel Engine Specifications
The Cummins 3.9-liter turbo diesel engine is part of the B-series of engines created by Cummins. Its trade name is the Cummins 4BT, a reference to its four cylinders, position as a B-series engine and the addition of a turbocharger. It is manufactured for use in commercial step vans, marine applications and agriculture, among other applications.
Type and Configuration
The 3.9-liter Cummins turbo diesel is an inline four-cylinder engine with four cycles. It features turbocharged aspiration that is not intercooled. The bore is 4.02 inches and the stroke is 4.72 inches. The first cylinder to fire is number one, followed by three, four and two.
Dimensions
The Cummins 4BT is 37.7 inches high, 30.6 inches long and 24.6 inches wide. It weighs between 745 and 782 pounds and has a gross vehicle weight rating of 16,000 pounds. It consumes 7.6 gallons of diesel per hour and the fuel pump operates at between 0.5 psi and 10 psi.
Cooling and Lubrication
The cooling system on the Cummins 3.9-liter engine can hold 8.8 quarts when allowing space for the coolant to expand. The engine thermostat allows temperatures between 181 and 203 degrees Fahrenheit. The oil pressure ranges from 10 psi while idling to 30 to 65 psi at normal operation. The engine can carry up to 10.4 quarts of oil and it can reach a maximum temperature of 250 degrees Fahrenheit.
Intake and Exhaust
The air intake system on the 4BT can pull in 270 cubic feet per minute. The exhaust gas flow is 700 cubic feet per minute at 900 degrees Fahrenheit.
Performance
The 3.9-liter turbocharged engine can produce 150 horsepower at 2,800 rpm and 265 foot-pounds of torque at 1,600 rpm. Its compression ratio is 17.5-to-1. The pistons operate at 2,205 feet per minute and the brake mean effective pressure is 177 psi.
Wednesday, October 9, 2013
How to Install an Oil Pump in a 6 5 Turbo Diesel
General Motors manufactured a 6.5-liter diesel engine from 1992 to 1999. It typically had a turbocharger and was most common in heavy trucks made by General Motors during this period. The purpose of the oil pump is to lubricate the moving parts by circulating oil through the engine. The oil pump on the General Motors 6.5-liter turbo diesel engine is under the engine, and is part of the oil pan assembly.
Instructions
- 1
Raise the vehicle and support it on jack stands. Place a drain pan under the drain hole in the crankcase. Remove the drain plug with a socket wrench, and let the oil drain into the pan. Replace the drain plug.
2Rotate the crankshaft manually so that the No. 1 and No. 2 connecting rods are in the up position. Remove the mounting bolts for the oil pan with a socket wrench. Lower the oil pump to gain access to the fuel pump.
3Disconnect the mounting bolts for the oil pump with a socket wrench. Allow the oil pump and its extension shaft to fall into the oil pan. Detach the pan from the vehicle.
4Mount the new oil pump into position on the main bearing cap. Align the extension shaft with the oil pump drive and push the pump into place. Fasten the mounting bolts for the oil pump and tighten them to 65 ft. lbs. with a torque wrench.
5Install the oil pan with a socket wrench and lower the vehicle. Fill the engine with oil. Start the engine and correct any oil leaks.