Tuesday, May 20, 2014
What Is the Difference Between 5 7 Vortec Heads Regular 350 Heads
Engine technology is both a passion and an obsession for car engineers and car aficionados alike. This is due to the fact that the modern internal combustion engine is an imperfect design and could benefit from a few tweaks to squeeze out more power and efficiency from the system.
The Vortec line of cylinder heads was introduced by GM in 1988 as a V6 with a 4.3-liter displacement. This technology created a vortex or pressurized swirl of fuel and air mixture inside the combustion chamber that enables the engine to produce more power while still gaining a marginal amount of fuel efficiency.
Vortec Means Power
Vortec heads instantly added 55 or more horsepower to a regular 350 head with the same displacement. Automotive enthusiasts are quick to note that the 350 and the 5.7 Vortec are essentially the same engine with the same displacement. The 350 designation is the cubic inch measurement that also translates to 5.7 liters.
It is hard to tell the two cylinder heads apart when it comes to the physical aspect of the build, but there are major differences that make Vortec heads more powerful and efficient.
5.7 Vortec Heads and Regular 350 Heads
The intake port of the Vortec head is different and measures 160cc with a modified port that increases the flow velocity. The bowl area is wider around the guide compared with regular 350 heads.
The intake bolt pattern is different and utilizes an eight-bolt attachment. The bolt pattern and the number casting is the quickest way to differentiate a Vortec Head from a regular 350 head. The Vortec head is available in two casting numbers (10239906 and 12558062) that offer identical performance virtues. You can also check the casting mark on the end of the head and check for three triangular saw-tooth casting marks that indicate Vortec potency.
Vortec Intake Valve Seats and Combustion Chamber
The intake valve seat of the Vortec head has a three-angle grind straight from the factory and the combustion chamber design is a radical departure from former GM heads utilized in the market. The Vortec combustion chamber is a kidney-shaped design that promotes better combustion and will have the spark plug located near the center of the chamber.
The regular 350 head utilizes a 90 degree intake bolt angle while the Vortec makes do with a 72 degree bolt angle. Experienced mechanics are all too familiar with the lay out of a Vortex head as all the attachment bolts point straight up when the head is bolted to the engine.
Conclusion
The Vortec head is without a doubt engineered towards producing more power, torque and engine response while improving overall fuel economy. If you plan to change or modify the head of the 350 engine in your car, installing a Vortec head alone will yield positive effects in your quest for power and speed.
Friday, March 21, 2014
How to Install an Electric Fuel Pump in a 1997 Ford 7 3
A 1997 Ford vehicle may have a variety of engine sizes, including an 8-cylinder 7.3-liter diesel engine. This engine is in the larger pickup trucks, such as a F-250 or F-350. The 1997 Ford 7.3-liter engine uses fuel injection and requires a high-pressure electric fuel pump. The fuel pump in a Ford diesel engine is accessible from the engine compartment and its replacement requires you to first relieve the pressure in the fuel system.
Instructions
- 1
Disconnect both ground cables from the battery with a socket wrench to prevent accidental sparking from the battery. Loosen the filler cap for the fuel tank by 1/2 turn to relieve the pressure in the fuel tank. Open the filler cap completely.
2Raise the vehicle with a floor jack and support it on jack stands. Locate the electrical connector for the fuel pump in the engine compartment. It is behind the fuel pump and next to the frame rail. Detach the electrical connector from the fuel pump.
3Locate the retaining clip for the fuel line to the fuel pump. Slide the retaining clip off of the quick connect fitting for the fuel line. Remove the fuel pumps fuel line from the fuel pump with the fuel line tool.
4Remove the clips for the brake line from the bracket of the fuel pump. Disconnect the pinch bolt on the mounting bracket with a socket wrench and spread the bracket open. Detach the fuel pump from its mounting bracket.
5Install the new fuel pump by performing steps one through four in reverse order. Start the engine and check for fuel leaks.
Thursday, November 14, 2013
How to Replace the Oxygen Sensor in a 2002 Dodge RAM 4 7
The oxygen sensors on a 2002 Dodge Ram 4.7-liter engine regulate the amount of oxygen burned in the engine, and they improve fuel efficiency and reduce pollution. Over time, the Rams sensors can become ineffective, causing the Dodge to have poor fuel economy and produce excess pollution. The 2002 Dodge Ram 4.7-liter engine has two oxygen sensors, and replacing them when necessary can make your truck more fuel-efficient.
Instructions
- 1
Locate the Rams oxygen sensors. They are located on either side of the catalytic converter on the exhaust system, and they look similar to a spark plug with an electrical wire at the end.
2Remove the Rams wiring harness. Pull off the wire at the end of the pickups oxygen sensors. Do not damage the end of the wire harness.
3Remove the Rams oxygen sensors from the exhaust system, using an oxygen sensor wrench.
4Apply anti-seize compound to the threads of the oxygen sensors and the threads into which they connect.
5Insert the new oxygen sensors, using a wrench to tighten them onto the Rams exhaust system. Reconnect the wiring harness to the oxygen sensors by pressing firmly until they click into place.
Wednesday, November 13, 2013
How to Take the Cylinder Head Off a 7 3 Ford Diesel
International Harvester manufactured the 7.3-liter diesel engines that appear in Ford trucks from 1988 to 1992. This engine is most common in Ford trucks with a rated carrying capacity of at least 1/2 ton. The 7.3-liter Ford diesel engine uses a single cylinder head for all eight cylinders in the engine. The cylinder head is on top of the engine block and is part of the combustion chamber. The procedure for removing the cylinder head from a 7.3-liter engine is the same for all Ford trucks.
Instructions
- 1
Disconnect the cables from the negative terminals of both batteries with a socket wrench. This prevents anyone from starting the engine while removing the cylinder head.
2Put a drain pan under the radiator. Remove the drain plug with a socket wrench and allow the coolant in the radiator to drain into the pan. Store the coolant for later use.
3Detach the shrouds for the radiator fan with a socket wrench. Disconnect the fan and clutch for the radiator as an assembly by using tools T83T-6312-A and T83T-6312-B. The mounting nut for the radiator fan and clutch has a left-hand thread, so you must turn it clockwise to remove the nut.
4Label the electrical wiring on the alternator so you can connect it correctly later and detach the wiring from the alternator. Disconnect the bolts for the alternator and vacuum pump with a socket wrench. Remove these components from the engine block.
5Disconnect the coolant hose from the cylinder head with a socket wrench. Remove the fuel injection pump from the engine block. Disconnect the intake manifold and valley cover from the engine block.
6Raise the vehicle with a floor jack and support it with jack stands. Remove the exhaust pipes from the exhaust manifolds with a socket wrench. Disconnect the clamp and mounting bolt for the oil dipstick tube. Detach the oil dipstick tube from the cylinder head and lower the vehicle.
7Disconnect the valve covers with a socket wrench and remove the rocker arms from the engine block. Record the position of each push rod, so you can re-install them correctly later. Remove the push rods from the engine block.
8Remove the fuel injector nozzles and glow plugs from the engine block with a socket wrench. Disconnect the mounting bolts for the cylinder head with a socket wrench. Install lifting eyes on each end of the cylinder block with tool T70P-6000.
9Lift the cylinder head from the engine block with the lifting eyes. Use caution to prevent the pre-chambers of the cylinder head from falling onto the engine when you remove the cylinder head.
Saturday, November 2, 2013
How to Change Fuel Injectors on a 1987 RX 7
The RX-7 is a sports car manufactured by Mazda from 1978 to 2002. The 1987 model is a second generation RX-7, which includes the 1986 through 1988 model years. The standard engine in the 1987 Mazda RX-7 was a naturally aspirated 1.3-liter engine with fuel injection. The fuel injectors are accessible from the engine compartment, but you will need to remove the throttle body from the engine to access the fuel injectors.
Instructions
- 1
Start the engine and disconnect the electrical connector for the fuel pump. Wait for the engine to stall, and then turn the ignition switch off. Disconnect the cable to the batterys negative terminal with a socket wrench. This will prevent the accidental discharge of fuel while you replace the fuel injectors. Replace the electrical connector for the fuel pump.
2Disconnect the accelerator cable from the throttle linkage with a socket wrench. Detach the cruise control cable and air funnel from the vehicle. Cover the fuel lines to the throttle body with a shop towel to catch spilled fuel. Disconnect the fuel lines and plug the open ends of the fuel lines with shop rags.
3Detach the electrical connector for the throttle position sensor connector. Disconnect the rod for the oil pump with a throttle-actuating lever with a socket wrench. Remove the retaining screws for the throttle body assembly and detach the throttle body assembly from the dynamic chamber.
4Disconnect the fuel line and fuel pipe from the fuel injectors with a socket wrench. Remove the electrical connectors for the fuel injector and disconnect the pressure regulator. Disconnect the distribution pipe from the fuel injector and remove the fuel injector from the vehicle. Discard the O-rings for the fuel injector.
5Install the new fuel injectors and O-rings by performing Steps 2 through 4 in reverse order. Connect the cable to the negative terminal on the battery with a socket wrench. Turn the ignition on for a few seconds to pressurize the fuel system. Start the engine and check for fuel leaks.