Monday, November 17, 2014
Outback Rear Alignment Specifications
The 2010 Subaru Outback came in six trims, but the rear alignment specs were the same for all. However, the alignment specs for 2010 should not be applied to other model years. For instance, the rear wheels of a 2010 Outback should have toe-in, while the rear wheels of a 2009 Subaru should have toe-out. This is significant, as inaccurate toe settings are the leading cause of tire wire due to misaligned wheels. Also, the caster is not adjustable on the rear end of the 2010 Outback.
Camber
The camber angle is the measurement of the way a wheel tilts as it is viewed from the front or rear of the vehicle. If the top tilts outward, away from the center of the vehicle, then the wheel has positive camber. If the wheel tilts inward, toward the center of the vehicle, the the wheel has negative camber. The ideal camber angle setting for the rear end of the 2010 Subaru Outback is zero but it can range by 0.75 degrees in either direction.
Toe
Toe is the angle of a wheel in relation to the centerline of a vehicle. Most vehicles are designed for a wheel to have toe-in, meaning the fronts of the wheels will angle slightly inward toward the centerline of the vehicle. Toe-in is given in positive degrees or inches, while toe-out is given in negative degrees or inches. The toe-in on the rear end of a 2010 Subaru Outback should be set at +0.17 degrees, but it can range by 0.25 degrees in either direction. Tires should wear less the closer they are set to the ideal angle.
Thrust Angle
As with toe, thrust angle is related to the way that the wheels are angled in relation to centerline of the vehicle. However, thrust angle ers specifically to the angle of the rear wheels. It is never adjustable on the front end, and on vehicles where the toe is not adjustable on the rear end, the thrust angle must be compensated for by adjusting the toe on the front end. The thrust angle on the rear end of the 2010 Subaru Outback should be +0.5 degrees.
Wednesday, March 26, 2014
How to Adjust a Rear Brake Pedal on a Harley Road Glide
The original equipment connection between the rear brake pedal and the rear brake master cylinder on all Harley-Davidson Road Glides to date is completely mechanical and not hydraulic. The mechanical connection is the same whether your Road Glide is equipped with your original brake pedal or an aftermarket pedal.
Instructions
- 1
Sit down next to the right side of your motorcycle and find the brake pedal.
2Find the rear brake master cylinder which is approximately parallel to the bottom of the brake pedal and about two feet closer to the rear of the bike. Then find the metal rod that connects the two.
3Loosen the jam nut that connects the rear brake cylinder to the brake rod by turning the nut counterclockwise with an open end wrench.
4Turn the brake rod with an open end wrench fitted to the flattened section of the brake rod. Turn the rod clockwise to lower the pedal and counterclockwise to raise the pedal.
5Tighten the jam nut by turning it clockwise when the brake pedal is adjusted to the proper height.
6Inspect the cotter pin that locks the brake rod to the brake pedal assembly. Use pliers to replace the cotter pin if it is broken or very corroded.
Monday, February 24, 2014
How to Repair the Rear Driver Side Window in a 2000 Malibu
Any broken window in a car can become a major frustration. Nobody wants to have to deal with the lack of security, unwanted objects flying inside your car, and noisy wind constantly blowing while you are driving. Rather than having to tape layers of plastic wrap over your broken window, or pay costly shop fees, you can replace the window with only a few tools.
Instructions
- 1
Remove the door trim panel. Use screwdriver and trim removal tool (or flat screwdriver) where appropriate to either unscrew pieces holding the trim on or pry them off where there are no screws. If your car has a manually operated window handle, use the trim removal tool to remove the handle. If your car has any electrical components located in the door trim, disconnect the electrical connectors as necessary to remove the trim. Remove the plastic water deflector that is between door and the trim panel.
2Clean up any broken glass. Depending on how your old window broke, there may be pieces of broken glass inside your door. Use a broom or vacuum to remove these pieces of broken glass.
3Remove the old window glass. Remove the window-to-channel nuts that are located at the bottom of the glass. You may have to lower the window glass to gain access to these nuts. Use the appropriate sized socket to remove the nuts. Place the nuts somewhere safe to avoid losing them. Remove the rubber sealing strip on the inside top of the door. Remove the old glass from the door by pulling it up and through where the rubber strip was.
4Install the new window glass. Insert the new glass the same way that the old glass was removed. Put back on and tighten the window-to-channel nuts. Put back on the rubber seal that was removed. Put the door trim and any pieces that were removed with it, as well as the plastic water deflector, back on.
Sunday, February 2, 2014
How to Replace the Rear Oxygen Sensor on a 2005 Nissan Altima
The 2005 Nissan Altima exhaust system includes two oxygen sensors. The upstream sensor is located near the exhaust manifold at the front of the exhaust system. The downstream sensor is located near the catalytic converter, further along the exhaust pipe. When a sensor fails, your "Check Engine" light will illuminate. If the "Check Engine" light is on and you notice a decrease in your fuel mileage, an oxygen sensor is the likely problem. Buy a replacement sensor from an auto-parts counter and change it at home in minutes.
Instructions
- 1
Lift the Altima using a jack until it is high enough to fit a set of jack stands under. Rest the car on the jack stands.
2Locate the downstream oxygen sensor threaded into the exhaust pipe, approximately halfway down the car, below the center console area. Press the tab on the electrical connection while you pull the connectors apart to disconnect it.
3Remove the sensor with a wrench or ratchet fitted with an oxygen sensor socket. Coat the new sensors threads with anti-seize compound, then hand-thread the sensor into the pipe.
4Push the electrical connection together until it clicks. Remove the jack stands by lifting the car slightly with the jack. Lower the Altima to the ground.
Friday, January 31, 2014
How to Replace the Rear Wheel Bearings on a Yamaha DT
Wheel bearings are circular parts located in the hub of a motorcycle wheel. When the bearings are working correctly they allow the wheel to spin freely. This part of the motorcycle is one which is overlooked and requires constant repair to ensure it works correctly. Finding the correct wheel bearings for the Yamaha DT is important. The information can be found in the vehicles manual. If a grinding noise comes from the wheel or the wheel wobbles when it moves, the bearings will need replacing immediately.
Instructions
- 1
Place the motorbike securely on the stand so that the rear wheel is elevated. Check to see if the wheel spins freely. Ensure that the bike cannot move at all before you begin.
2Use the wrench to remove the muffler by by loosening the drive clamps and heat shield.
3Take off the axle nut with the wrench and use the wooden mallet to tap the axle free from the wheel. Move the axle to a safe place to avoid it being damaged.
4Caully remove the brake disc from the brake caliper and slip the drive belt from its socket. Pull the rear wheel away from the frame and place it on a flat surface to work on.
5Gently tap the bearings out from around the wheel using the long drift bar. Ensure that the bearing does not become twisted around the hub. Repeat the process on the opposite side.
6Align the bearings where the old ones were. Use the old bearings to softly tap the new bearing in place. Turn the wheel over and fit the second bearing the same way
7Reattach the wheel to the Yamaha DT following the removal steps in reverse. Spin the wheel to ensure it moves freely.
Thursday, January 23, 2014
Rear Disc Brake Tools
The rear disc brake on an automobile requires the use of a variety of specialty tools, when repairing or replacing it. Many of these tools are available at most auto parts stores, but some need to be ordered, or purchased, through an automotive tool supplier.
Disc Brake Piston Tool
The disc brake piston tool is used to adjust the rear disc brakes on automobiles. This disc brake piston tool is used with a wrench and driver set. The piston tool looks like a cylinder, which fits around the piston and has a square hole, located in the middle of the cylinder, where the driver fits in place.
Rear Brake Caliper Kit
Rear brake caliper kits are used on rear disc brakes, where the pistons are tied to the parking brake. When the pistons and parking brake are tied together, it requires the parking brake to be turned and pushed back, in order to gain access to the rest of the brake systems. It comes with different size adapters, in order to fit most domestic and import automobiles.
Disc Brake Caliper Spreader
The disc brake caliper spreader is a tool used when the parking brake is not tied into the pistons. The caliper spreader is used to open the calipers, which hold, and press, the brake pads against the brake rotor. In order for the brake pads to be removed, the brake calipers need to be opened wide, or pressed open, with the caliper spreader. The disc brake caliper spreader looks like a small flat plate, with a rod and handle, which turns or screws, so the calipers can be pressed open.
Electronic Brake Fluid Tester
The electronic brake fluid tester is used to check the moisture in the brake fluid. The brake fluid tester looks like a test tube that has LED lights, which inform the mechanic of the quality of the brake fluid. A little moisture in the brake fluid is acceptable, but this brake fluid tester has different colored lights, which tell how much moisture is in the brake fluid, so the mechanic can make a decision on whether to flush the rear brake lines and replace the fluid.
Brake Shoe Retaining Spring Tool
The brake shoe retaining spring tool is a tool used on the rear disc brakes, to install or remove the retaining spring on the brake shoes. It comes with different size ends, which fit four different size springs. The brake-shoe retaining spring tool has a handle, located in the middle, so the mechanic can turn the tool.
Tuesday, December 17, 2013
How to Remove a Rear Bumper Bar From a Toyota Cressida
There are many reasons why you may need to remove the rear bumper on your Toyota Cressida. It is possible that your bumper has been damaged in an accident or that you just want to upgrade to a fancy one. Fortunately, this is a job you can do right at home with very little mechanical ability or experience. Be ready to spend about an hour to remove your bumper. You just need to purchase a few tools that can be found at any hardware store.
Instructions
- 1
Park your vehicle in a comfortable workspace and set your parking brake.
2Open the trunk of your car using the ignition key. Use the Phillips screwdriver to remove the screws on the inside of the trunk where the plastic cover hides the bumper bolts.
3Remove the four bolts that secure the bumper using a socket wrench.
4Remove the screws that hold part of the bumper from the underside of the rear wheel fender wells. These screws are located near the rear bumper.
5Use a flat-head screwdriver to pry apart the rivets that hold the plastic part of the rear bumper to the metal part.
6Pull off the rear bumper using your hands. It may take a little force to pull it off if it has any dirt or grime in the connection areas.
Friday, September 27, 2013
What Does a Bad Rear Wheel Bearing Do
Wheel bearings allow the wheels on your car to rotate with minimal friction and support your cars weight. Most rear wheel bearings are engineered to last about 150,000 miles but sometimes they fail prematurely thanks to poor adjustment, contamination or loss of grease. If you want to keep your car running properly, youll need to keep your rear wheel bearings in near-perfect condition.
Make Noise
The first symptom of bad rear wheel bearings is usually noise. You might hear rumbling, growling or chirping coming from the vicinity of your rear wheels. Once you hear this noise, you need to take your car in to have it serviced immediately. Expect the amount of noise your rear wheel bearings are making to be proportional to the speed you are driving, whether you are accelerating, coasting or decelerating. The noise might sound different while you are making turns or disappear at some speeds entirely. Most bad rear wheel bearings are identified when drivers complain about this noise.
Play
Bad rear wheel bearings may also result in play. Play can allow steering wander. This means that although you are holding your steering wheel still, your car drifts to the left or right as you drive. Play can be dangerous for drivers, especially on highways. Play reduces the amount of control you have over your vehicle. If your rear wheel bearings are sealed and they play, that is a sure sign that they need to be replaced. If the rear wheel bearings are adjustable, you or your mechanic may be able to adjust the bearings after removing, cleaning and inspecting them. Play is usually a sign that your rear wheel bearings are worn, but it could also mean that the hub nut backed off or the bearings were not properly adjusted.
Turn Your ABS Light On
If your anti-lock brake system light is on and you cant for the life of you figure out why, check your rear wheel bearings. If your car is equipped with anti-lock brakes and sealed hub assemblies with an integral anti-lock brake sensor or tone ring, the ABS light will come on if a wheel speed sensor is reading erratically or has no signal. The anti-lock brake system will set a fault code corresponding to the sensor location and disable the anti-lock brake system until the fault is fixed. The only way to fix this is to replace your hub assembly. You cant repair a sealed hub assembly and must replace the entire unit.
Cause Your Car to Lose Its Wheels
In the most extreme of cases, ignoring your bad rear wheel bearing can cause your car to lose a wheel. One of the rear wheels on your vehicle may fly right off while you are cruising down a highway, placing everyone in its path in danger. Losing a wheel on a freeway while traveling at high speeds could result in a deadly accident. Thus, if you have any reason to believe that your rear wheel bearings are bad, you must immediately take your car to a mechanic to have them examined.
Thursday, September 26, 2013
1999 Plymouth Breeze Torque Specifications for a Rear Hub Bearing
The Plymouth Breeze was a mid-sized automobile produced from 1996 to 2000 and offered with either a 2.0L or 2.4L engine. The vehicle sold well and is still a common sight on the road. If your 1999 Breeze has developed a high-pitch squeal emanating from the rear wheels, you should suspect that a bearing is worn. Proper installation of a wheel bearing requires that you tighten the attaching bolts or lock-nut to the proper torque.
Bearing Overview
The rear suspension of a 1999 Plymouth Breeze uses standard shock absorbers. The rear wheels use sealed type wheel bearings, which are not serviceable. They are designed to last the life of the vehicle, but this is rarely the case. Often the bearings can be damaged, allowing dirt and water to enter. This causes the bearing to wear rapidly, requiring you to eventually replace the bearing.
Rear Wheel Bearing Description
The rear wheel bearings are a combined unit. The five bolts that protrude from the hub flange support the brake drum and wheel and are what the wheel lug nuts attach to. The hub and bearing assembly is attached to the rear knuckle spindle and held on with a single lock nut. If you remove this lock nut for any reason you must replace it with a new one.
Checking the Bearings
Jack up and support the rear of your Plymouth Breeze. Remove the rear wheels and brake drums. Inspect the bearings for grease. Slowly rotate the hubs, feeling for roughness, resistance or lateral movement, any of which may indicate that you need to change the hub/bearing assembly.
Rear Bearing Removal
To remove the rear bearings, first jack up and support the rear of your Plymouth. Remove the rear wheels and brake drums. Use a flat-head screwdriver to pry off each metal hub dust cap. Use a socket wrench to remove the hub lock nuts. Pull the hub/bearing assemblies straight out of the spindles. When reassembling the bearing and hub assemblies, tighten the new lock nuts to 185 foot-pounds. Torque the wheel lug nuts to 95 foot-pounds.