Showing posts with label torque. Show all posts
Showing posts with label torque. Show all posts

Friday, May 2, 2014

What Causes a Lock Up Torque Converter in the Transmission

Theres nothing wrong with a locked-up torque converter; as a matter of fact, lock-up torque converters have been making automatic transmissions more efficient for decades. Youll only encounter brief periods during your driving cycle where converter lock-up is not beneficial.

Converter Operation

    Torque converters are fluid couplers. A turbine fan attached to the outer case (which is bolted to the engine) pushes transmission fluid through a matching turbine on the transmission input shaft. The engine doesnt push enough fluid when idling to engage the transmission turbine. As rpm rises, that fluid will begin to push against and spin the transmission-side turbine, engaging it and moving the car.

The Problem

    Because there was no direct connection between the engine and transmission, a non-lock-up converter will always get worse fuel mileage than a manual transmission, which uses a clutch.

Lock-Up Function

    A lock-up converter uses a clutch pack very similar to those inside the transmission itself to lock the converter case to the transmission input shaft. At about 25 mph, the computer sends a signal to an electronic actuator inside the transmission to engage the clutch pack and lock the drive line together.

Read More.. >

Monday, April 28, 2014

Instructions to Adjust an AmPro Torque Wrench

Instructions to Adjust an AmPro Torque Wrench

AmPro tools are manufactured by Frenway Products. Frenway has been in business since 1984 and provides tools and services to 63 countries around the world. Using an AmPro torque wrench allows you to set your own torque specifications for your chosen project. Torque settings are very important when you are working with different engine bolts. If you use too much torque on certain bolts, you may break them and make it harder, if not impossible, to remove from the hole. Always check your bolt torque specifications before you set your torque wrench.

Instructions

    1

    Hold your AmPro wrench in one hand. With the other hand, grab the locking knob at the end of the torque wrench and turn it counterclockwise to unlock the torque setting.

    2

    Adjust the handle to your desired torque setting. Start by rotating the handle so the setting reads "0" on the minor graduation scale. The "0" is also in line with vertical scale on the shaft. Both of these scales are in inch pounds (in/lb).

    3

    Raise or lower the handle to adjust the vertical scale setting. The vertical scale has large numbers (120, 360, 600, etc.) listed in a vertical fashion on the handle.

    4

    Rotate the handle to your desired setting on the minor graduation scale. This adjustment allows you to add small amounts of torque to your vertical scale setting. "1" on the minor graduation indicates 1 foot/lb and is equal to 12 inch/lb. For example, if you raise the handle on the vertical scale to 360 inch/lb and then rotate the minor scale to "2", you will be adding 24 inches to your 360 setting to make it a setting of 384 inch/lb.

    5

    Rotate the locking knob clockwise to secure your setting into place.

Read More.. >

Sunday, February 9, 2014

2002 Mustang Front Hub Torque Specs

2002 Mustang Front Hub Torque Specs

First introduced in 1964, Mustang is one of the most successful Ford car models. The fourth generation of Ford Mustang is powered by various types of engines and featured sharper contours, larger wheel arches and new interior design.

Important Note

    Suspension fasteners are important as they affect performance of the main components and systems of the suspension. Major service expenses can be expected if they fail. Only new parts with the same part number must be installed, if service or replacement is required. During reassembly, to ensure correct retention of these parts, only specified torque values must be used.

Torque Specification

    Front wheel hub and bearing retainer nuts must be tightened using 258 foot-pounds of torque.

Part Replacement

    The original equipment manufacturer (OEM) part number for the front hub and bearing is 1R3Z1104BA and the manufacturers recommended price is $145 (as of February 2011).

Read More.. >

Sunday, January 26, 2014

How to Torque Exhaust Manifolds

Using a torque wrench to tighten bolts on exhaust manifolds allows for precise setting of the torque, or tightness of the fastener. Both loose and tight bolts can be dangerous, so you must follow the specifications for your car exactly or expect them to break.

Instructions

    1

    Have your torque specs handy. These can be found in the owners manual of your car or exhaust manifold. You may need to hunt around online or ask a mechanic if you are without a manual.

    2

    Use high-grade bolts to fasten your parts. Manifolds play key roles in the exhaust system, so you dont want to skimp on quality. Choose at least a level 5 bolt for your car or motorcycle. The higher level means a better quality component to trust in your car.

    3

    Install your exhaust manifold if it is not yet in your engine. Simply finger-tighten the bolts, starting first from the inside and working outwards. Tightening fasteners in the wrong sequence may damage your manifold.

    4

    Check to make sure all the bolts are in place. Manifolds must have every bolt installed to avoid cracking. You cant skip a fastener in a car just because parts feel secure when you install them.

    5

    Tighten the exhaust manifolds bolts using a torque wrench. Each bolt needs to be tightened according to the torque specs for your car. The torque wrench helps you tighten and loosen bolts to a set amount in pounds.

    6

    Work in a spiral pattern from the middle section to the outer bolts, starting with the even bolts. The outer bolts usually have a smaller torque weight for adjustment. Make sure you adjust the torque wrench accordingly.

    7

    Stop turning the bolt when you feel the wrench stop working. Avoid over-tightening, which can cause the bolts to break. Always fall within the proper torque range, which you should have set on your wrench.

    8

    Visit a site like TorqueSpecs.com to check your torque specs after 2 weeks to make sure your bolts are tightened properly (see Resources below). This site has many common specs for various car parts. Whenever installing exhaust parts or systems, it is a good idea to check to see how the parts settled during use.

Read More.. >

Friday, January 17, 2014

Hydraulic Torque Wrench Setup Instructions

A hydraulic torque wrench is an industrial torque wrench capable of tightening bolts accurately up to 150,000 foot-pounds of torque. Hydraulic torque wrenches are lightweight and portable devices; however, they require the use of a 10,000-psi pump. Setting up your hydraulic torque wrench is a relatively straightforward process that requires you to hook the pump up to the wrench head and set the necessary torque value using the air pressure of the pump.

Instructions

    1

    Connect a male 10,000-psi hydraulic pump hose from the female connection on the torque wrench to the female connection on the 10,000-psi pump.

    2

    Connect a female 10,000-psi hydraulic pump hose from the male connection on the torque wrench to the male connection on the 10,000-psi pump.

    3

    Twist the metal connectors on both ends of each hose clockwise until secure.

    4

    Connect the pump to an available power outlet if it is an electric pump or to an air-pressure source if it is an air-driven pump.

    5

    Locate the desired torque value on your torque conversion chart. Scroll over to determine the corresponding hydraulic pressure value that you must set on the pump.

    6

    Loosen the locking ring on the adjustable relief valve on the pump. Turn the thumbscrew clockwise to increase the amount of pressure the pump can contain or counterclockwise to decrease the amount of pressure the pump can contain.

    7

    Press and hold the "Advance" button on the pump remote control to fill the pump until the pump gauge reaches the desired pressure.

    8

    Tighten the locking ring on the adjustable relief valve once pressure is set to the desired level.

    9

    Connect the desired impact socket to the torque wrench head and insert the locking pinion into the socket.

    10

    Apply the torque wrench head to any bolt you wish to tighten, ensuring that the reaction arm (long portion of the torque wrench head) presses against an adjacent surface.

Read More.. >

Wednesday, November 13, 2013

Differences Between Torque Wrenches

Differences Between Torque Wrenches

Automotive repairs often require exact settings when tightening fasteners to ensure that parts are properly fastened. The various bolts and fasteners used to assemble an automobile have different tensile strengths, and stresses produced by operation of the vehicle require these fasteners to accommodate these stresses without failing. To place the proper tension on a fastener without exceeding its tensile strength, different types of torque wrenches are used when tightening them.

Digital Torque Wrench

    Digital torque wrenches use an electronic display to show the amount of torque applied with the wrench. These wrenches are usually switched between metric measurements and SAE measurements and are also easily set to display torque in either foot pound or inch pound increments. The displays on the wrenches are electrically powered and use either an LCD or LED display screen mounted on the handle to show torque numbers.

Clicker Torque Wrench

    Clicker torque wrenches signal when the desired amount of torque is reached by emitting an audible click. These wrenches include a spring inside the handle that places a load on an internal lever. The amount of tension in the spring is adjusted by turning the sleeve on the bottom of the handle to the desired torque level indicated on the handle. When the proper amount of torque is applied, the force applied to the wrench overcomes the spring-loaded lever within the handle, causing it to emit an audible click as it releases. Because these wrenches use a spring to preload an internal lever, you reset them back to zero after each use because prolonged compression of the spring degrades the strength of the spring and reduces the wrenchs accuracy.

Beam Wrench

    Beam torque wrenches are the most common type of torque wrench. They have a long pointer beam mounted parallel to the handle shaft. When torque is applied to a bolt, the handle shaft bends but the pointer beam remains straight. The end of the pointer beam then matches up to an indicator mounted to the handle shaft, which shows how much torque is applied. You must observe the indicator on these wrenches from a straight-on view to accurately read the torque readings.

Dial Indicator Torque Wrench

    Dial indicator torque wrenches operate similarly to beam-style torque wrenches. Instead of having a separate pointer beam over an indicator mounted on the handle, the beam is enclosed within a housing and moves the indicator on a dial as torque is applied. The dial indicator is easier to read than the indicator on the beam wrench and some dial indicator wrenches include lights or buzzers to indicate when the desired torque setting is reached.

Read More.. >

Thursday, September 26, 2013

1999 Plymouth Breeze Torque Specifications for a Rear Hub Bearing

The Plymouth Breeze was a mid-sized automobile produced from 1996 to 2000 and offered with either a 2.0L or 2.4L engine. The vehicle sold well and is still a common sight on the road. If your 1999 Breeze has developed a high-pitch squeal emanating from the rear wheels, you should suspect that a bearing is worn. Proper installation of a wheel bearing requires that you tighten the attaching bolts or lock-nut to the proper torque.

Bearing Overview

    The rear suspension of a 1999 Plymouth Breeze uses standard shock absorbers. The rear wheels use sealed type wheel bearings, which are not serviceable. They are designed to last the life of the vehicle, but this is rarely the case. Often the bearings can be damaged, allowing dirt and water to enter. This causes the bearing to wear rapidly, requiring you to eventually replace the bearing.

Rear Wheel Bearing Description

    The rear wheel bearings are a combined unit. The five bolts that protrude from the hub flange support the brake drum and wheel and are what the wheel lug nuts attach to. The hub and bearing assembly is attached to the rear knuckle spindle and held on with a single lock nut. If you remove this lock nut for any reason you must replace it with a new one.

Checking the Bearings

    Jack up and support the rear of your Plymouth Breeze. Remove the rear wheels and brake drums. Inspect the bearings for grease. Slowly rotate the hubs, feeling for roughness, resistance or lateral movement, any of which may indicate that you need to change the hub/bearing assembly.

Rear Bearing Removal

    To remove the rear bearings, first jack up and support the rear of your Plymouth. Remove the rear wheels and brake drums. Use a flat-head screwdriver to pry off each metal hub dust cap. Use a socket wrench to remove the hub lock nuts. Pull the hub/bearing assemblies straight out of the spindles. When reassembling the bearing and hub assemblies, tighten the new lock nuts to 185 foot-pounds. Torque the wheel lug nuts to 95 foot-pounds.

Read More.. >

Sunday, September 22, 2013

Sears Torque Wrench Operating Instructions

Sears Torque Wrench Operating Instructions

Shade tree mechanics are likely to use two main types of torque wrenches. "Beam type" torque wrenches are cheaper and require the user to read an analog scale that stretches across a beam on the top of the wrench just under the handle. With a "click type" torque wrench the mechanic sets the desired torque on a round gauge, and the head of the wrench slips when the fastener is tightened to that preset value. Sears sells more torque wrenches than any other company in the United States.

Instructions

    1

    Wear safety glasses, because metal fasteners sometimes break. Attach a socket to the torque wrench.

    2

    Disregard torque readings less than 20 percent of the full scale. Do not estimate torque readings greater than 100 percent of the full scale.

    3

    Inspect and distrust any torque wrench you drop or that you suspect may have been dropped by someone else.

    4

    Store click-type torque wrenches with the gauge set to the lowest setting. Always store them in protective cases.

    5

    Apply a specific torque value to a fastener with a torque wrench only during final tightening. Never use a torque wrench as the primary means of tightening or loosening fasteners. Use a socket wrench instead.

    6

    Grasp a torque wrench in the center of the handle, because torque wrenches are length specific. If you must use two hands, put one hand on top of the other.

    7

    Torque a fastener with a slow, steady movement. Never jerk a torque wrench.

    8

    Recalibrate a torque wrench after every 5,000 uses.

Read More.. >