Showing posts with label front. Show all posts
Showing posts with label front. Show all posts

Wednesday, April 23, 2014

My Front Wheel Hub Wont Come Off

My Front Wheel Hub Wont Come Off

The front wheel hub keeps the rim and tire attached to a car with lug nuts. The problem with the front wheel hub is that the rim can become oxidized in place. This can make for an annoying tire change if you run into problems. Getting your wheel off the wheel hub is not very hard to do. You dont have to take your car into a service shop to perform this task. You can do it yourself with little hassle.

Instructions

    1

    Jack the car up from the front end so the wheel hub is lifted off the ground. Remove the lug nuts from the rim with a tire iron. Keep the lug nuts together so they arent lost.

    2

    Spray a penetrating lubricant like WD-40 onto the entire wheel hub. Make sure that the lubricant seeps into the cracks under and around the connection from the wheel to the wheel hub.

    3

    Use a pry bar to remove the wheel from the car. Insert the pry bar into the crack where the wheel meets the hub. Put pressure on the pry bar until you feel the wheel coming loose from the hub.

    4

    Use the pry bar all around the wheel until it comes free from the wheel hub.

Read More.. >

Monday, March 31, 2014

How to Change the Front Wheel Hub in a 1998 Intrigue

The front wheel hub assembly on a 1998 Oldsmobile Intrigue contains both the bearing, hub, and wheel studs. This wheel hub assembly is non-repairable and must be replaced as an entire unit. Symptoms of a faulty hub assembly include a noticeable vibration that increases with vehicle speed, grinding or buzzing when turning, and howling or whining at speeds above 45 miles per hour. The hub assembly is secured to the steering knuckle with three steel bolts. These bolts must be replaced when installing the new hub assembly.

Instructions

Removal

    1

    Apply the parking brake and chock the rear wheels. Remove the hub cap on the affected side by loosening the hub cap locking caps with a 19 mm socket and a ratchet. Break the lug nuts loose with a 19 mm lug nut wrench.

    2

    Raise the vehicle with an automotive jack and support it with two jack stands, one on each side. Check to make sure the vehicle is securely supported before proceeding.

    3

    Remove the lug nuts with a 19 mm lug nut wrench and remove the tire. Have an assistant depress the brake pedal and loosen the axle shaft nut one revolution with a deep-well axle nut socket and a ratchet.

    4

    Place a C-clamp over the brake caliper so one end of the clamps is over the rear side of the caliper and the other end of the clamp is over the outer brake pad. Loosen the caliper bleeder screw with a flare nut wrench, then tighten the C-clamp to compress the caliper piston. Tighten the bleeder screw immediately after compressing the piston.

    5

    Remove the bolts holding the brake caliper bracket to the knuckle and pry the caliper and bracket off of the rotor together. Tie the caliper and bracket assembly to the strut spring with a piece or wire.

    6

    Remove the brake rotor. Place a pry bar in between the wheel studs to hold the hub still, then remove the axle shaft nut. Loosen the three bolts on the back side of the steering knuckle that hold the hub assembly in place with a ratchet and metric socket. Install a two-jaw puller onto the hub flange. Center the puller screw on the end of the axle shaft. Tighten the puller screw to force the splined portion of the axle shaft out of the hub assembly.

    7

    Remove the puller from the hub assembly. Remove the bolts that hold the hub assembly to the steering knuckle and remove the hub assembly from the vehicle.

Installation

    8

    Clean the circular hub assembly mating surface on the steering with a wire brush to remove any excess corrosion. Apply a light coating of grease to the axle splines. Slide the axle into the new hub assembly and rotate it until the three mounting holes align with the holes in the steering knuckle.

    9

    Reinstall three new hub assembly mounting bolts with a ratchet and metric socket. Torque the bolts to 96 foot-pounds with a torque wrench.

    10

    Set the brake rotor into position on the new hub and install two lug nuts to hold it in place. Slide the brake caliper and bracket into position over the rotor and reinstall the brake caliper bracket bolts. Tighten the bracket bolts to 137 foot-pounds using a torque wrench. Have an assistant hold a pry bar in between the axle nut studs to immobilize the hub, and then install a new axle nut on the axle spindle and torque it to 118 foot-pounds. Double-check to make sure that the brake caliper, bracket, hub assembly, and rotor are properly installed before proceeding.

    11

    Reinstall the wheel and tighten the lug nuts using a lug nut wrench. Lift the vehicle off of the jack stands with an automotive jack and set it on the ground. Torque the lug nuts to 100 foot-pounds with a torque wrench and reinstall the hub cap.

    12

    Pump the brakes until the pedal firms up; because the piston was driven back into the caliper bore, you must pump the brakes to move the piston forward into contact with the brake pads before operating the vehicle. Road test the vehicle to ensure that hub assembly and brakes operate properly.

Read More.. >

Saturday, March 22, 2014

How to Remove Front Seats on a Ford Escape

Removing the front seats from your Ford Escape may be necessary if the seats need replacing, the carpet need to come out, or if you wish to replace the seats with aftermarket models. Damage to the seats or tracks can make them unstable, making safety of the seats a concern or affecting their comfort. Replacement seats are available from the Ford dealer or through some specialty auto-parts suppliers.

Instructions

    1

    Locate the seat adjuster on the outside edge of the seat. Move the seat all the way forward, then locate the two retaining bolts that secure the seat track to the floor behind the seat. Remove both bolts with a socket and ratchet, setting the bolts in a safe place for reuse later.

    2

    Move the seat to the rear until it is all the way back, then locate the front mounting bolts under the seat. Remove the bolts from the floor and mounting brackets with a socket and ratchet. Set the bolts aside for now.

    3

    Raise the front of the seat and locate the wiring harness connection under the seat. Depress the locking tab on the connector and separate the wiring harness pigtail from the connection on the base of the seat.

    4

    Lift the seat and caully remove it through the door opening. Set it aside, keeping it off the ground, in a dry location. Repeat the process to remove the second seat from the front of your Escape, if required.

Read More.. >

Wednesday, February 26, 2014

Heavy Truck Front End Alignment Tools

Heavy Truck Front End Alignment Tools

Many auto repair shops are equipped to perform alignment adjustments on regular cars and trucks, but aligning the front ends of buses, RVs or heavy-duty trucks often requires the use of specialized tools. The types of tools used include primary tools such as alignment gauges and axle-correction tools, as well as an array of supplemental tools like wheel-rim straightening tools, wheel-weight tools and lug-nut-cover tools. Adjusting the alignment of a heavy vehicle is not something an amateur should attempt, especially since most shops rely on heavy-duty lifts or a pit to access the underside of vehicles.

Alignment Guages

    Because accurately measuring the angles of several aspects of a wheel, particularly the caster, camber and toe, is crucial to correcting the alignment, alignment gauges are perhaps the most important tool when aligning the front ends of heavy-duty vehicles. Companies such as Specialty Products Company, Josam and Bee Line sell manual, computerized and laser alignment gauges. Specialty Products Company offers manual heavy-duty gauges for around $200, as of December of 2010, while Bee Line offers portable and stand-alone computerized gauging systems that use laser measuring the company claims is accurate to 1/1000 of an inch. Bee Line must be contacted for pricing on its computerized systems, and these systems may require additional tools, accessories and training.

Axle Correction Tools

    Axle correction is the only way to adjust the camber to the ideal settings on heavy-duty vehicles such as semi tractors. Bee Line and Josam offer portable and pit-based axle-correction tools capable of applying up to 130 tons of pressure to the axle in order to adjust the camber. Axle-correction tools consist of a steel beam with hydraulic rams connected to it. The beam of the tool is fastened to the axle, and the hydraulic rams extend, applying tons of pressure and bending the axle.

Other Tools

    There are a wide array of other tools that can be necessary or beneficial to adjusting the alignment of a heavy-duty truck, depending on the vehicle and the types of adjusts being made. Turntables make it easier to move heavy-duty alignment systems from bay to bay or from location to location. Slip plates allow a wheel to move freely while it is being adjusted. A tandem axle caliper can be used to measure the distance between axles of a semi-tractor. A rim-straightening tool can be sued to manually straighten dents and bends in wheel flanges or rims.

Read More.. >

Sunday, February 9, 2014

2002 Mustang Front Hub Torque Specs

2002 Mustang Front Hub Torque Specs

First introduced in 1964, Mustang is one of the most successful Ford car models. The fourth generation of Ford Mustang is powered by various types of engines and featured sharper contours, larger wheel arches and new interior design.

Important Note

    Suspension fasteners are important as they affect performance of the main components and systems of the suspension. Major service expenses can be expected if they fail. Only new parts with the same part number must be installed, if service or replacement is required. During reassembly, to ensure correct retention of these parts, only specified torque values must be used.

Torque Specification

    Front wheel hub and bearing retainer nuts must be tightened using 258 foot-pounds of torque.

Part Replacement

    The original equipment manufacturer (OEM) part number for the front hub and bearing is 1R3Z1104BA and the manufacturers recommended price is $145 (as of February 2011).

Read More.. >

Thursday, October 31, 2013

How to Replace a Front Sway Bar on a Jeep Wrangler

The sway bar or stabilizer bar on the front of the Jeep Wrangler is in place to keep the body from rolling on the suspension and improve the handling of the Jeep. You can replace the sway bay if necessary; replacement sway bars are available from Jeep and some auto parts stores. The sway bar on the front of your Jeep Wrangler runs over the top of the frame, making access to the mounting hardware much simpler than on other vehicles.

Instructions

    1

    Use a lug wrench to loosen the lug nuts on the front wheels, then raise the front of the Jeep off the ground with a jack. Position a set of jack stands under the front axle of the Jeep to support it, then remove the front tires and set them aside.

    2

    Locate the nut on the top of the stabilizer bar end link near the front coil spring. Use a wrench to remove the nut from the top of the end link and set it aside. Repeat on the opposite side of the Jeep, then lift the sway bar off the end links.

    3

    Move to the front of the Jeep and use a socket and ratchet to remove the four retaining bolts that secure the plastic valance on the frame just behind the bumper. Remove the valance to expose the sway bar bushings and mounts on top of the frame.

    4

    Use a ratchet and socket to remove the four bolts that hold the sway bar mounts to the frame. Lift the U-shaped retainers off the sway bar and set them aside. Lift the sway bar off the frame and remove it from the truck. Slide the bushings off the old bar and save them.

    5

    Slide the bushings onto the new sway bar after applying a small amount of grease to the inside of the bushing. Position the bushing and bar on the frame and install the U-shaped brackets over the sway bar and bushings.

    6

    Use a socket and ratchet to tighten the four retaining bolts. Install the plastic valance, tightening the retaining bolts until they are snug. Be careful not to crack the plastic valance.

    7

    Slide the sway bar onto the top of the end links near the coil spring on both sides of the suspension and thread the retaining nuts onto the top of the link. Torque the bolts to 45 ft.-lbs. with a torque wrench.

    8

    Install the front wheels and thread the lug nuts onto the wheel studs. Raise the front of the Jeep off the jack stands, then remove the stands from under the Jeep. Lower the jack until the tires are on the ground. Tighten the lug nuts with a lug wrench.

Read More.. >