Showing posts with label wrangler. Show all posts
Showing posts with label wrangler. Show all posts

Friday, April 4, 2014

Jeep Wrangler Transmission Problems

Jeep Wrangler Transmission Problems

On November 3, 2009, Chrysler LLC and the National Highway Traffic Safety Administration (NHTSA) announced a recall of 88,461 Jeep Wrangler vehicles for transmission problems that could potentially cause a fire.

Defect

    According to Chrysler and the NHTSA, certain model year 2007-2008 Jeep Wranglers manufactured from June 2006 through July 2008 and equipped with automatic transmissions were erroneously not equipped with a temperature warning system.

Risk

    A fire may result if fluid boils over and comes into contact with the hot engine, per the NHTSA. This could cause personal injury to consumers and/or damage to property.

Remedy

    Dealers must inspect and install a "hot oil" message in the instrument cluster and warning chime indicating an elevated transmission fluid condition, according to the NHTSA.

Notification

    Chrysler mailed notification to registered vehicle owners with instructions to bring the affected Jeep Wranglers to authorized dealers for repair in February 2010. Concerned drivers who did not receive notification may contact Chrysler or NHTSA to determine whether their Jeep Wranglers might be subject to these transmission problems.

Read More.. >

Saturday, December 21, 2013

How to Remove a Wrangler TJ Shifter

Removing the transmission shifter from your Jeep Wrangler requires removal of the center console inside the Jeep. From there you can access the bolts that hold the shifter in place. The shifter is unlikely to fail as a unit, but if it does you can perform this removal with little effort. A new shifter is available from the Jeep dealer or you can source a used shifter through a salvage yard.

Instructions

    1

    Sit in the Jeep and grasp the handle on the top of the shifter. Pull it straight up, popping it off the shaft. It will come off hard but that is normal.

    2

    Remove the cover in the base of the cup holder, using a small screwdriver to pry it out. Pop the trim bezel loose around the shifter using a flat screwdriver or trim stick then lift it over the top of the shifter.

    3

    Remove the bolts under the trim bezel and in the cup holder with a socket and ratchet. Lift the console over the shifter and set it aside.

    4

    Locate the wiring harness connection on the side of the shifter, depress the locking tab on the connection and separate the two halves. Disconnect the shifter cable from the side of the shifter by popping the retaining clip loose from the mount pin with a screwdriver, then pull the cable off the pin.

    5

    Remove the four bolts securing the shifter to the floor using a socket and ratchet. Lift the shifter off the floor and remove it from the Jeep.

Read More.. >

Thursday, October 31, 2013

How to Replace a Front Sway Bar on a Jeep Wrangler

The sway bar or stabilizer bar on the front of the Jeep Wrangler is in place to keep the body from rolling on the suspension and improve the handling of the Jeep. You can replace the sway bay if necessary; replacement sway bars are available from Jeep and some auto parts stores. The sway bar on the front of your Jeep Wrangler runs over the top of the frame, making access to the mounting hardware much simpler than on other vehicles.

Instructions

    1

    Use a lug wrench to loosen the lug nuts on the front wheels, then raise the front of the Jeep off the ground with a jack. Position a set of jack stands under the front axle of the Jeep to support it, then remove the front tires and set them aside.

    2

    Locate the nut on the top of the stabilizer bar end link near the front coil spring. Use a wrench to remove the nut from the top of the end link and set it aside. Repeat on the opposite side of the Jeep, then lift the sway bar off the end links.

    3

    Move to the front of the Jeep and use a socket and ratchet to remove the four retaining bolts that secure the plastic valance on the frame just behind the bumper. Remove the valance to expose the sway bar bushings and mounts on top of the frame.

    4

    Use a ratchet and socket to remove the four bolts that hold the sway bar mounts to the frame. Lift the U-shaped retainers off the sway bar and set them aside. Lift the sway bar off the frame and remove it from the truck. Slide the bushings off the old bar and save them.

    5

    Slide the bushings onto the new sway bar after applying a small amount of grease to the inside of the bushing. Position the bushing and bar on the frame and install the U-shaped brackets over the sway bar and bushings.

    6

    Use a socket and ratchet to tighten the four retaining bolts. Install the plastic valance, tightening the retaining bolts until they are snug. Be careful not to crack the plastic valance.

    7

    Slide the sway bar onto the top of the end links near the coil spring on both sides of the suspension and thread the retaining nuts onto the top of the link. Torque the bolts to 45 ft.-lbs. with a torque wrench.

    8

    Install the front wheels and thread the lug nuts onto the wheel studs. Raise the front of the Jeep off the jack stands, then remove the stands from under the Jeep. Lower the jack until the tires are on the ground. Tighten the lug nuts with a lug wrench.

Read More.. >

Friday, October 11, 2013

How to Make an 89 Jeep Wrangler Fuel Efficient

The 1989 Jeep Wrangler has several attractive features. Unfortunately, excellent gas mileage is not one of them. Through troubled economic times, most Jeep Wrangler owners have had to compensate for this flaw by adopting some new driving practices, in an effort to increase overall fuel efficiency. Aside from making these changes, there are some products you can use to build and support engine performance, in turn helping the fuel burn more efficiently in your Jeep Wrangler.

Instructions

    1

    Pour a commercial fuel additive into your gas tank to clean out the combustion chambers in the engine.

    2

    Pour the oil additive into the oil filler cap on the engine to lubricate and rejuvenate the engine.

    3

    Replace the air and oil filters according to the instructions provided in your repair manual. Have regular tune-ups performed on the engine, and closely monitor your tire pressure.

    4

    Drive in low gears and avoid the use of four-wheel drive.

    5

    Roll down your windows rather than using the air conditioning.

Read More.. >