Friday, April 18, 2014
How to Replace the Oxygen Sensor on a 1989 Nissan Maxima
The 1989 model year brought a complete redesign of Nissans flagship sedan, the Maxima. Experts considered this version of the Maxima the most beautiful to date, and it was also significantly larger than previous models. The 1989 Maxima uses just one oxygen sensor to monitor the level of oxygen in the exhaust and send this information to the electronic control unit. The ECU then uses this information to adjust the air-to-fuel ratio in the combustion chamber to keep the Maxima at peak performance.
Instructions
Removal
- 1
Raise the front of the Maxima with a floor jack and slide jack stands under the vehicles subframe. Lower the Maxima onto the jack stands.
2Crawl under the middle of the vehicle and find the front pipe, the exhaust pipe just before the catalytic converter. Find the oxygen sensor screwed into the front pipe, just before the catalytic converter.
3Spray the base of the oxygen sensor with penetrating oil and allow it to sit for the time specified in the penetrating oil instructions.
4Trace the oxygen sensors wiring upward until you find where the sensors wiring harness plugs into the Maximas wiring harness. Unplug the oxygen sensors wiring harness.
5Remove the oxygen sensor from the front pipe, using a ratchet and oxygen sensor socket.
Installation
- 6
Apply a coating of anti-seize compound to the new oxygen sensors threads and hand-tighten the sensor into the front pipe.
7Tighten the sensor to 15 foot-pounds using a torque wrench and oxygen sensor socket.
8Apply a small amount of dielectric grease to the inside of the oxygen sensors wiring harness and plug the sensors harness into the Maximas wiring harness.
9Raise the vehicle off the jack stands and remove the stands. Lower the vehicle to the ground.
Tuesday, March 18, 2014
My 87 Nissan Van Wont Start
Problems with a Nissan van starting can occur for a variety of reasons but the battery and the fuel levels are the primary reasons it will not start. Many people consult a mechanic when their cars will not start, but you can troubleshoot the issues yourself. Corrosion on the battery terminals, a dead battery, or no gas in the van will probably be the reason your Nissan van will not start.
Instructions
- 1
Pop the hood to the Nissan van and locate the battery next to the engine.
2Look the battery connections over for any corrosion. Use a socket wrench to loosen the terminal connections.
3Clean the terminals with soda and a wire brush and then connect the terminals back onto the battery.
4Try to restart the car. If the car does not start, jump-start the van with jumper cables and another car.
5Leave the van running for at least five minutes and then turn the car off. Try to restart the van. If the van does not restart, replace the battery.
6Add 1 gallon of gas to the van and then try to restart the van. If the van restarts, get a mechanic to repair your fuel gauge.
Wednesday, February 26, 2014
How to Change the Tensioner Pulley on a Nissan Xterra
Cars with a serpentine belt are equipped with a tensioner pulley, which puts pressure on the serpentine belt to hold it in place. If the serpentine belt comes loose due to a malfunctioning tensioner pulley, the belt will slip out of place and you could lose power to several systems, including the alternator, air conditioning, and power steering.
Instructions
- 1
Pull the emergency brake and chock the wheels of the car. This is an important safety step, as it prevents the car from rolling or moving while you are working on it.
2Open the hood and determine the location of your serpentine belt and tensioner. This will be on the front of your engine block. If your car does not have a routing diagram for the serpentine belt on the underside of the hood, draw a diagram on a spare sheet of paper.
3Place the head of the 3/8-inch drive ratchet in the hole of the tensioner pulley, and apply pressure counterclockwise to remove pressure from the serpentine belt, then remove the belt from around the tensioner pulley. There is no need to remove the belt from all of the pulleys that it services. Move the belt far enough from the tensioner so that you have ample room to work.
4Determine what socket size you need to remove the tensioner and tensioner pulley. The bolt head that you need to loosen is the one located on the front of the tensioner, as opposed to the one on the tensioner pulley. Using the socket and ratchet, loosen and remove the bolt.
5Remove the tensioner assembly from the engine and place it to the side.
6Install the new assembly and replace and tighten the bolt until it is secure. Make sure that the bolt is tightened well, as engine vibration can cause a loose bolt to work itself loose.
7Replace the serpentine belt around the tensioner pulley and er to the routing diagram to ensure that it remains in its proper position around the other pulleys. Insert the ratchet head into the hole on the front of the pulley and apply pressure in a counterclockwise direction to reapply pressure to the serpentine belt.
Sunday, February 2, 2014
How to Replace the Rear Oxygen Sensor on a 2005 Nissan Altima
The 2005 Nissan Altima exhaust system includes two oxygen sensors. The upstream sensor is located near the exhaust manifold at the front of the exhaust system. The downstream sensor is located near the catalytic converter, further along the exhaust pipe. When a sensor fails, your "Check Engine" light will illuminate. If the "Check Engine" light is on and you notice a decrease in your fuel mileage, an oxygen sensor is the likely problem. Buy a replacement sensor from an auto-parts counter and change it at home in minutes.
Instructions
- 1
Lift the Altima using a jack until it is high enough to fit a set of jack stands under. Rest the car on the jack stands.
2Locate the downstream oxygen sensor threaded into the exhaust pipe, approximately halfway down the car, below the center console area. Press the tab on the electrical connection while you pull the connectors apart to disconnect it.
3Remove the sensor with a wrench or ratchet fitted with an oxygen sensor socket. Coat the new sensors threads with anti-seize compound, then hand-thread the sensor into the pipe.
4Push the electrical connection together until it clicks. Remove the jack stands by lifting the car slightly with the jack. Lower the Altima to the ground.
Saturday, January 11, 2014
How to Troubleshoot a Nissan Altima 2 5
The Nissan Altima 2.5 is a four-door sedan. If you are having problems with your Nissan Altima 2.5 there are a few things that you can do before you take it to a Nissan dealership for repair. Common problems occur with the fuel, battery, and the cooling system. Checking these aspects of the car is not invasive and can be done by anybody with minimal knowledge of how the car works.
Instructions
- 1
Turn the key in the Altimas ignition to see if the instrument panel will turn on. If the instrument panel does turn on, check over the fuel level in the gas tank. If you dont have enough fuel to start the Altima fill it up. If the instrument panel does not come on, you have a problem with your battery.
2Open the hood from the hood latch on the grill. Open the hood and then locate the battery next to the engine block. Check over the connections from the battery cables to the battery terminals on the battery. Make sure that the connections are tight so the electricity can flow to the car. Use channel locks to tighten the connections.
3Test the battery if the car will not restart after the connections have been tightened. Use a voltmeter to test the 12-volt battery. If you are getting a reading below 11 volts, use a battery charger to charge the battery.
4Connect the positive and negative leads from the battery charger to the battery. Plug the battery charger into an electrical outlet and allow the charger to charge your battery overnight. Try to start the car the next morning. If the car wont start, have the battery replaced.
5Look over the cooling system if your Altima is overheating. The cooling system is on the left side of the engine block. A small tank holds the coolant. Check the coolant tank to make sure there is enough coolant in the system. Pour 50/50 coolant into the tank until it has reached the fill line to eliminate overheating.
Wednesday, December 18, 2013
How to Replace the Fuel Pump in a 1991 Nissan 240SX
The 240SX is a two-door compact car that Nissan sold in North America from 1989 to 1998. The 1991 model belongs to the first generation of the 240SX that was in production from 1989 to 1995. These vehicles were equipped with a 4-cylinder, 2.4-liter engine that uses sequential fuel injection. This type of fuel injection uses an electric fuel pump to deliver fuel at high pressure. The fuel pump for the 1991 Nissan 240SX is accessible from the trunk of the vehicle.
Instructions
- 1
Remove the fuse for the fuel pump from the fuse box under the dashboard. Start the engine and let it run until it stalls. Crank the engine twice to relieve the pressure in the fuel system. Turn the ignition off, and replace the fuse for the fuel pump.
2Disconnect the cable for the negative terminal on the battery with a socket wrench to prevent accidental sparking. Open the rear trunk and disconnect the electrical connector for the fuel gauge. Remove the cover for the fuel tank. Disconnect the fuel lines from the fuel pump assembly.
3Remove the retaining bolts for the fuel pump assembly with a socket wrench. Lift the fuel pump assembly out of the fuel tank, and discard the O-ring on the fuel tank. Plug the resultant opening in the fuel tank with a clean shop rag to keep dirt out of the fuel tank.
4Remove the shop rag from the fuel tank opening. Install a new O-ring onto the fuel tank. Place the new fuel pump assembly into the fuel tank, and fasten the fuel pump assemblys retaining bolts with a socket wrench. Attach the fuel lines and electrical connection, and replace the cover for the fuel tank.
5Connect the cable to the negative terminal of the battery with a socket wrench. Start the engine and check the fuel system for leaks.
Friday, November 22, 2013
How to Remove the Exhaust Manifold on Nissan Datsun
Nissan Datsun was a joint venture between the two popular car companies. Together they produced some of the most fuel efficient and popular vehicles on the road. The exhaust manifold on a Nissan Datsun directs exhaust gases out of the engine and through the tailpipe. If you ever need to replace or want to upgrade your manifold to a high-flow model, remove the old one first.
Instructions
- 1
Open the hood of your Nissan Datsun and remove the air cleaner assembly. There are several screw bolts holding the assembly in place. You can use either a socket wrench or a screw to remove these types of bolts.
2Locate the exhaust pipe. This will be located next to the air cleaner assembly you just removed.
3Unbolt the exhaust manifold where it connects to the intake manifold using the socket wrench.
4Unbolt the exhaust manifold where it connects to the exhaust pipe using the socket wrench.
5Pull the temperature sensors out of the manifold.
6Disconnect any miscellaneous hoses from the exhaust manifold. Some models may not be equipped with them. For example, you may need to pull the EGR valve hoses off from the manifold. These hoses help recirculate the exhaust gases, but must be removed to get the manifold out. Usually, these are held in place with hose clamps. To loosen the hose clamp, unscrew the retaining screw bolt (counterclockwise) and the clamp will loosen so that you can pull the hose.
7Loosen the nuts on the manifold connecting it to the engine and lift the manifold out of the engine bay.
Saturday, November 9, 2013
How to Replace a Nissan Altima Catalytic Converter
The catalytic converter on your Nissan Altima cannot be repaired if it is defective. Replacement is the only option in these cases. Replacement catalytic converters are available from most auto parts stores but for the best fit, replacements from the dealer are a better option. The converter gets very hot when the car is running so be sure to allow the car to sit for about an hour before attempting this repair.
Instructions
- 1
Raise the front of your Maxima with a jack and a set of jack stands under the front suspension. Lower the jack, allowing the car to rest on the stands, and then remove the jack.
2Crawl under the car. Locate the catalytic converter underneath the center of the car. Four bolts attach the heat shield to the bottom of the catalytic converter case. Remove the bolts with a socket and ratchet then removed the heat shield from the converter body.
3Locate the flanges at each end of the catalytic converter and remove the bolts on both ends with a wrench. Pull the converter out from between the two exhaust pipe sections and discard it.
4Lift a new converter into place and insert a new gasket between the exhaust flange and the converter flange on both ends. Install two mounting bolts on each end then tighten them with a socket and ratchet.
5Install the heat shield using four mounting bolts and tighten them with a socket and ratchet. Raise the car off of the jack stands with your jack, and then remove the stands from under the car.
6Lower the car to the ground and remove the jack from under the front on the car.
Wednesday, November 6, 2013
How to Replace the Exhaust System on a Nissan Pathfinder
Replacing the exhaust system as a whole or in pieces requires some inspection of the components to determine what is damaged or worn out. The exhaust system is responsible for removing spent gases and fumes from the engine and out the back of the vehicle. If it has holes or leaks, it can become dangerous to the passengers inside the vehicle. You can purchase the parts of the system in sections or buy the whole system at most auto parts stores.
Instructions
- 1
Raise your Pathfinder off the ground with a jack. Support it with jack stands under all four corners of the truck. Make sure the truck is high enough that you can work under it comfortably while still being stable.
2Remove the clamp holding the tailpipe to the rear of the muffler by loosening the nuts on the clamp with a wrench and separate the two pipes. Remove the tail pipe from the hanger at the rear of the truck by pulling the pin on the pipe out of the rubber hanger on the truck and working the pipe loose from the muffler. Move the pipe out from under the truck.
3Locate and remove the bolts that secure the muffler to the front right and left exhaust pipes. These are the pipes that come down from the exhaust manifolds.There is a flange on each pipe with a gasket and two bolts that hold the muffler to these pipe sections.
4Remove the two hangers that hold the muffler up by removing the bolts from them using a ratchet and socket. There are two on each hanger. Drop the muffler down to the ground and remove it from under the truck.
5Remove the nuts from the manifold studs where the front pipes attach. There are two nuts on each pipe and a bronze O-ring that seals the pipe to the manifold. Remove the pipes and O-rings and discard them.
6Install a new right and left front pipe after installing the new bronze O-ring in the pipe. Slide the pipe onto the manifold studs then install the nuts. Tighten the nuts with a socket and ratchet until they are secure and do not move around.
7Install the new muffler to the front pipes and install a new gasket in between the two flanges. Insert the mounting bolts and tighten them with a wrench or socket and ratchet. Reinstall the hangers and tighten the bolts with a socket and ratchet or wrench.
8Install the new tailpipe by sliding the tailpipe onto the pipe exiting the rear of the muffler and slide the hanger pin into the rubber hanger at the rear of the truck. Install a new exhaust clamp on the joint between the muffler and tail pipe and tighten the nuts with a wrench or socket and ratchet.
9Remove the jack stands from under the truck and use a jack to carefully lower the truck down to the ground.
Saturday, October 12, 2013
How to Replace the Third Light on a 2000 Nissan Altima
Replacing the bulb in the high mount taillight on the rear of your 2000 Nissan Altima can help to prevent a rear end collision. It allows following drivers to notice your braking sooner. The high mount brake light contains two 921 bulbs and replacements are at any auto parts store, department store or the dealer. Changing the bulbs will only take a couple minutes and does not require tools.
Instructions
- 1
Climb into the back seat of your Altima and locate the third brake light housing on the rear package deck. Grasp the edges of the third brake light assembly and push it toward the rear of the car using light, even pressure. Do not push so hard that you break the glass.
2Lift up on the housing, removing it from the rear deck. There are wires under the housing so do not pull it to far out or you will damage the wiring.
3Turn the housing so you can access the bulbs and pull them straight out of the sockets. Install new 21 bulbs.
4Position the light housing, pushing it slightly forward and down and slide it back. The housing will lock in place.
Friday, September 20, 2013
2002 Nissan Sentra Alignment Specifications
First introduced on the U.S. market in 1982, Sentra is a compact family car manufactured by Nissan and sold worldwide. All Sentra sedans require periodic adjustment, often referred to as "alignment." The factory specifications for the alignment are the same for all 2002 Sentra models. These specifications are given for a vehicle at curb height with one-half tank of fuel.
Camber
Measured in degrees, camber is the outward or inward tilt of the wheel in relation to the center of the vehicle. The Sentra camber angle should be the same on both left and right wheels. Camber angles must be 50.25 degrees with the measuring accuracy of 0.45 degrees on the front wheels and -1.00 degrees with the measuring accuracy of 0.45 degrees on the rear wheels.
Caster
Caster is both the rearward and the forward tilt of the steering knuckle from the true vertical. Caster is the measurement in angles that is responsible for directional stability. The Sentra caster angle should be the same on both rear and front wheels. The angle must be +1.36 degrees with the maximum allowable difference of 0.85 degrees.
Toe
Toe is the difference between the leading and trailing inside edges of the front wheels. Total toe angles on the Sentra models must be +0.11 degrees with measuring range of 0.05 degrees. Toe-in specification should be set at 2 mm with maximum allowable difference of 1 mm.