Tuesday, May 6, 2014
How to Reset the Traction Control Light on the 2000 V70 Volvo
The Volvo V70 wagon is equipped with an advanced traction control system that actively monitors the wheels to ensure proper traction. When the system senses a loss of traction, it retards the engine timing until traction increases. The entire traction system is monitored and controlled by the ABS computer. When the ABS computer detects an issue with the traction control system, it turns on the traction control light. In addition to turning on this light, it records a trouble code that corresponds directly to the problem. Automotive technicians can retrieve this trouble code with an automotive scan tool in order to diagnose and repair the system. In order to reset the traction control light, this code must be erased from the ABS computers memory.
Instructions
- 1
Stop the engine and turn the ignition forward to the RUN position so that the dashboard lights are illuminated.
2Find the V70s communications port under the dashboard on the drivers side of the passenger cabin. This port is a 16-pin receptacle that is mounted just out of view, under the leading edge of the dashboard.
3Plug the scan tools connector into the communications port. Turn on the scan tool and wait while it starts up. Most scan tools run an automatic check of their memory, similar to home computers, before arriving at the menu screen.
4Look caully at the scan tools screen. Use the menu button on the scan tool to navigate to the ABS menu. Select the option to clear the trouble codes from the ABS computers memory. Watch the screen for a confirmation message that the codes are cleared.
5Use the menu keys to navigate back to the home screen and power down the scan tool. Disconnect the cable from the communication port and start the engine. Verify that the traction control light is not on or blinking. If the light is off then the traction control system is reset.
Tuesday, December 3, 2013
How to Replace the Control Arm Bush on a Toyota Hilux
The Toyota Hilux was a light truck made from 1976 to 1995. It was designed for off-road driving and reliability. The off-road ability of the Hilux is made possible in part by its control-arm suspension setup. The control arms help focus the kinetic energy of bumps into the shock absorbers. This puts the control arms under large amounts of stress; bushings are used to protect the connecting bolts. These bolts can become too soft over time, and require replacement.
Instructions
- 1
Shift the car into "park." Set the emergency brake. Jack up the corner of the car. Slide in a jackstand. Remove the wheel with your tire iron; place it to the side.
2Place the jack under the steering knuckle; support the knuckle with the jack stand. The control arm is U-shaped; the two arms connect to the Hiluxs frame. The bottom part of the U is connected to the steering knuckle. Unbolt the two back-arms from the trucks frame. Lower the jack so that the arms are no longer blocked by the supporting flanges on the frame.
3Push the old bushings out of the arms bolt-holes with a flathead screwdriver. If the bushings are stuck, hit the screwdriver with a rubber mallet. Do not hit the control arm itself. Cracks on a suspension-part might grow due to mechanical stresses.
4Push the new bushings into place on the control-arm bolt holes. Slide the bolts back into place on the control-arm bolt holes. Wrench them down flush. Remove the jack and bolt the wheel back on. Lower the truck off the jack stand.
Tuesday, November 26, 2013
How to Adjust Cruise Control on a Jeep CJ7
If you spend a lot of time driving on the highway, you probably are familiar with your cars cruise control. It can make driving long distances more comfortable and increase your fuel economy. Older vehicles with mechanical cruise controls occasionally require adjustments to keep them operating at peak efficiency. If your Jeep CJ7s cruise control engages at a higher or lower speed than youve selected, follow the procedure outlined below.
Instructions
Speed-centering Adjustment
- 1
Locate the cruise-control module underneath the instrument panel on the drivers side. On one side near the mounting tabs are two adjustment screws.
2Adjust the screw closer to the mounting tabs in the following manner: If the cruise control engages two or more miles per hour faster than the selected speed, turn the adjusting screw counterclockwise a quarter-turn. If the cruise control engages two or more miles per hour slower than the selected speed, turn the adjusting screw clockwise a quarter-turn.
3Drive the vehicle on a level road to check for proper adjustment. Repeat the steps above as necessary.
Thursday, September 26, 2013
How to Use a NOx Control
A NOx control sensor measures the nitrogen oxide that a car puts out. If this sensor fails, a car will not pass its emissions test. To test the NOx sensor on a car, use an On-Board Diagnostic (OBD) scanner. You do not have to be a car mechanic to do so.
Instructions
- 1
Turn off the ignition and locate the cars Data Link Connector. This is a 16-pin plug that an OBD scanner plugs into, and is generally located under the cars steering wheel.
2Connect the OBD scanner to the Data Link Connector. Switch on the ignition. Turn on the OBD scanner.
3Press the Read button on the scanner. (Some scanners will have a Scan button instead.) Wait for the troubleshooting codes to appear on the scanners display.
4Look up the troubleshooting code in the scanners manual to see if the NOx sensor is faulty. If the sensor is faulty, you must have it replaced to pass an emissions test.
5Unplug the scanner from the car and turn off the ignition.