Showing posts with label arm. Show all posts
Showing posts with label arm. Show all posts

Monday, May 19, 2014

What Is an Idler Arm

Proper steering control is crucial to driving safety, allowing the driver to maintain accurate control of the vehicle. The idler arm is a component of the steering system in a vehicle. Not all cars have steering systems. Most sport utility vehicles (SUVs) and trucks have steering systems, as do some passenger models.

Identification

    The idler arm consists of a ball joint, an arm and pivot bushing. The idler arm is on the passenger side of the frame rail.

Function

    The idler arm connects the steering box to the center link. The center link is what turns the hubs and allows a vehicles tires to rotate. The idler arm controls the passenger side steering in a vehicle.

Problems

    A faulty idler arm usually leads to the car pulling to one side. Drivers may also notice one tire is more worn than the other. A loose steering wheel is another indicator of a worn out idler arm. Drivers may also notice a noise when turning corners.

Read More.. >

Sunday, December 8, 2013

How to Remove a Pitman Arm on a K1500

Removing the pitman arm from your Chevy K1500 requires a pitman arm puller as the arm-to-sector shaft clearance is extremely tight. The arm is not quite a press fit, but it is so tight that you cannot drive or pry the arm off the steering box. You can heat the arm with a torch to expand it, but you will still need to press it off the shaft with the puller. A pitman arm puller can be rented at most auto parts stores if you do not have one.

Instructions

    1

    Locate the pitman arm under the front of the truck on the drivers side. The tie rod is attached to the lower portion of the pitman arm and the steering box sector shaft on the upper portion.

    2

    Remove the cotter pin from the tie rod end with a pair of pliers and discard it. Place a socket and ratchet on the tie rod nut and rotate it counterclockwise, removing the nut from the tie rod end.

    3

    Place a tie rod separator between the tie rod end and the pitman arm. Drive the separator in with a hammer, forcing the tie rod end out of the pitman arm. Lay the tie rod aside.

    4

    Locate the nut on the end of the sector shaft at the top end of the pitman arm. Place a socket and breaker bar on the nut and turn it counterclockwise to free the nut, then replace the breaker bar with a socket and remove the nut from the shaft.

    5

    Place the two arms from a pitman arm puller on the pitman arm directly below the sector shaft. Turn the shaft in the center of the puller clockwise with a socket and ratchet, forcing the pitman arm off the sector shaft.

Read More.. >

Tuesday, December 3, 2013

How to Replace the Control Arm Bush on a Toyota Hilux

The Toyota Hilux was a light truck made from 1976 to 1995. It was designed for off-road driving and reliability. The off-road ability of the Hilux is made possible in part by its control-arm suspension setup. The control arms help focus the kinetic energy of bumps into the shock absorbers. This puts the control arms under large amounts of stress; bushings are used to protect the connecting bolts. These bolts can become too soft over time, and require replacement.

Instructions

    1

    Shift the car into "park." Set the emergency brake. Jack up the corner of the car. Slide in a jackstand. Remove the wheel with your tire iron; place it to the side.

    2

    Place the jack under the steering knuckle; support the knuckle with the jack stand. The control arm is U-shaped; the two arms connect to the Hiluxs frame. The bottom part of the U is connected to the steering knuckle. Unbolt the two back-arms from the trucks frame. Lower the jack so that the arms are no longer blocked by the supporting flanges on the frame.

    3

    Push the old bushings out of the arms bolt-holes with a flathead screwdriver. If the bushings are stuck, hit the screwdriver with a rubber mallet. Do not hit the control arm itself. Cracks on a suspension-part might grow due to mechanical stresses.

    4

    Push the new bushings into place on the control-arm bolt holes. Slide the bolts back into place on the control-arm bolt holes. Wrench them down flush. Remove the jack and bolt the wheel back on. Lower the truck off the jack stand.

Read More.. >