Friday, February 7, 2014
Rebuilt Vs Remanufactured Transmission
Rebuilt and remanufactured transmissions are readily available options for most vehicles. However, these terms mean something different, and knowing the differences can make a decision between the two easier.
Rebuilt
A rebuilt transmission usually is one that has been taken apart, and those components that were damaged or not functioning properly have been replaced. Usually, this is the less expensive of the two options. In this case only damaged or faulty components are replaced. All other components are used again.
Remanufactured
A remanufactured transmission is one where all vital components have been replaced, and only the cast parts, such as the outer shell, have been reused. These typically are more expensive, since more work has been done to the transmission. Also they tend to be more reliable, as they are nearly new.
The Warranty
Often, the same warranty will be offered with both types of transmission, although that for the remanufactured unit may be slightly longer. This is because typically if anything that is the fault of the rebuilder or remanufacturing company is going to malfunction, it will do so relatively early in the warranty. However, the longer the warranty, the longer you do not have to worry about replacement cost.
Tuesday, December 10, 2013
Resistor Vs Non Resistor Spark Plugs for an ATV
Resistor-type spark plugs perform a crucial function on ATVs. These spark plugs contain a 5-kilowatt ohm ceramic resistor core inside the spark plug shell. The resistor functions as a suppressor against electromagnetic interference, also know as radio frequency interference, when the ignition fires at high voltage. This electricity "noise" can disrupt vehicle radios, often in the form of a hissing, popping or crackling noise. There is a marked difference between resistor and non-resistor spark plugs regarding ATV ignition systems and performance.
Ignition and Voltage
ATV engines typically use a coil or magneto to produce a high-voltage spark that travels through the spark plug wire and to the spark plug. When the primary winding inside the coil is turned off or on, depending upon the type, it sends a signal to the secondary winding to activate. The secondary winding steps up the voltage from 12 volts to anywhere from 30,000 to 50,000 volts. This high voltage is required to create an arc between the spark plug ground and positive electrode. The high voltage creates a stray radio frequency noise.
Resistor vs. Non-Resistor -- Communications
The primary purpose of resistor spark plugs for an ATV is to allow them to soak up powerful radio wave frequency interference. Since the electromagnetic discharge of high voltage also has a radio frequency signal, it often interrupts and causes static in ATV radios, CB radios and GPS systems. The resistor plug acts as a voltage soak to suppress static, crackling and loss of communication signal. Without resistor plugs, particularly on an older model ATV, no suppression exists, and interference can be detected in communication devices at any engine rpm. The noise interference can take on an annoying whine, directly proportionate to the engine speed.
Resistor vs. Non-Resistor -- Ignition Backlash
On many off-road vehicles, the secondary systems, including resistor spark plugs, are used to reduce the high electrical backlash caused by the coils primary winding. The backlash, or extra electrical feedback, causes a disruption in the ignition system, such as the CDI boxes and igniters that are part of the ignition control modules. ATV vehicles that do not have such secondary resistor systems can show poor performance, such as periodic missing, rough idle and high-speed ignition cutout. ATVs and motocross bikes use resistor spark plugs to protect the ignition control modules.
Resistor vs. Non-Resistor -- Backlash and RFI
Radio frequency interference can cause disruptive signals to an ATVs sophisticated on-board computer, which links to the control modules. Secondary electrical systems close to the coil will cause backlash and high RFI, since their voltage signal is significantly stronger. Resistor spark plugs suppress RFI and electronic backlash, keeping communication systems clear and on-board computers from harm. Non-resistor spark plugs can cause radio, CB and GPS static interference, as well as disrupt the entire ignition system. Newer ATV models with computer management systems will sometimes not start or run poorly when fitted with non-resistor spark plugs, due to the sensitivity of the computer and module settings.
Older ATV models
ATV models manufactured before 1979, and some models prior to 1990, do not have computer engine management systems or microprocessors. Therefore, they do not have ignition problems related to radio frequency interference. These older off-road vehicles benefit from resistor spark plugs only in a communications application if they have been modified or fitted to accept a radio, CB or GPS system.
Resistor/Non-Resistor Advantages and Disadvantages
The advantages of a resistor spark plug are straightforward, in that it suppresses RFI, for communications and ignition systems. However, resistor material is often composed of carbon material, which deteriorates with age. The deterioration will cause a suppression failure, leading to radio frequency interference. This results in additional maintenance. Resistor spark plugs do absorb some of the coils maximum reserve output, and this reduction applies more to older vehicles in which the owner has installed non-resistor plugs in a system that never had or required them. Older ATV models that do not have computers or communication systems do not suffer any RFI-related problems.