Showing posts with label 4l. Show all posts
Showing posts with label 4l. Show all posts

Sunday, May 11, 2014

How to Install a Jeep Power Tech 2 4L Oil Pump

Chrysler has used the PowerTech brand for a variety of unrelated engines. One type of PowerTech engine is a four-cylinder 2.4-liter engine that appeared in the Jeep Liberty from 2002 to 2005. The oil pump on this vehicle circulates oil throughout the engine to provide lubrication for its moving parts. The Jeep PowerTech 2.4-liter engine has its oil pump on the crankshaft sprocket in front of the engine.

Instructions

    1

    Remove the cable from the negative terminal of the battery with a socket wrench. Disconnect the rear cover of the timing belt and loosen the timing belt tensioner. Detach the timing belt.

    2

    Disconnect the mounting bolts for the oil pan with a socket wrench. Remove the oil pan from the engine.

    3

    Remove the crankshaft sprocket with Special Tool 6793 and Special Tool C-4685-C2. Disconnect the crankshaft key with a socket wrench and detach the oil pick-up tube from the oil pump. Remove the oil pump and the crankshaft seal from the crankshaft sprocket. Discard the crankshaft seal.

    4

    Clean the mounting surfaces for the new oil pump with a shop rag and apply gasket sealer to the mounting surfaces. Install the O-ring into the discharge passage of the oil pump. Fill the oil pump with engine oil to prime it.

    5

    Align the rotor flats of the oil pump with the crankshaft flats. Install the oil pump to the block with a new crankshaft seal. Connect the crankshaft key with a socket wrench. Install the crankshaft sprocket with Special Tool 6792 to set the sprocket to the original depth.

    6

    Connect the oil pump pick-up tube to the oil pump. Mount the oil pan and fasten the mounting bolts with a socket wrench. Install the timing belt and connect the rear cover for the timing belt with a socket wrench.

Read More.. >

Tuesday, November 26, 2013

How Do I Change a Knock Sensor in a Ford 5 4L

How Do I Change a Knock Sensor in a Ford 5.4L?

A knock sensor is a piezometric crystal that advances or retards the engine based on load. Knock sensors are typically located on the intake side of the Ford 5.4-liter engine. All knock sensors connect to an electrical wiring harness and links to the vehicles On Board Computer (OBC). A knock sensors fails like a light bulb fails -- it simply wears out. When a knock sensor does fail, the OBC will automatically retard the engine to minimal fuel efficiency and put the engine in limp mode. The check engine light is a symptom of knock sensor failure.

Instructions

    1

    Disconnect the negative terminal from the vehicles battery using the 10- to 12-mm box wrench to prevent short-circuiting while changing out the knock sensor.

    2

    Disconnect the electrical wiring harness from the knock sensor by pulling it apart manually or using long-handled needle-nose pliers. This action is similar to pulling a plug out of an electrical wall socket.

    3

    Remove the knock sensor by attaching the wobble or swivel bit to the end of the 3/8-inch extension and fastening it to the socket that fits. Insert the socket over the knock sensor. You need the wobble or swivel bit at the end of the extension to access the sensor due to the configuration of the intake manifold.

    4

    Connect the ratchet to the end of the 3/8-inch extension that is attached to the wobble or swivel bit and the socket. Use the ratchet to loosen the sensor from the engine block by turning it gently to the left. Remove the defective sensor from the socket and place the defective sensor on the work bench.

    5

    Add a dab of white lithium grease to the male end of the electrical connections of the new knock sensor to prevent corrosion build up and to make insertion easier.

    6

    Use the socket with the extension to manually screw the new knock sensor to the engine block to avoid cross-threading. Cross-threading occurs when the threads of the sensor do not match up with the threads of the engine block.

    7

    Reattach the electrical harness to the sensor and reconnect the negative terminal of the battery.

Read More.. >