Showing posts with label procedures. Show all posts
Showing posts with label procedures. Show all posts

Tuesday, March 25, 2014

Replacement Procedures for a 2001 Avalon Thermostat

A faulty thermostat can cause a number of problems, such as engine overheating and reduced cooling system efficiency. Although the thermostat is a small, inexpensive component, its absolutely critical to the proper operation of a liquid-cooled engine. The 3.0-liter engine in a 2001 Toyota Avalon contains a thermostat thats designed to open at a temperature of 176 to 183 degrees Fahrenheit. The most common thermostat fault is a failure to open. In this situation, the thermostat valve doesnt open when it should, preventing coolant from properly circulating and causing the engine to overheat.

Instructions

Removal

    1

    Allow the engine to cool for at least two hours to prevent burns and other injuries related to the high temperate of the engine and engine coolant.

    2

    Raise the vehicle with a jack and support it with jack stands. Remove the radiator cap and place a drain pan underneath the radiator. Loosen the drain valve with a ratchet and metric socket. Allow the coolant to drain out until the stream flowing from the radiator slows to a drip. This may take 30 minutes or more. Close the radiator drain valve. Place the drain pan under the engine, beneath the thermostat housing.

    3

    Remove the bolts holding the V-bank cover in place at the top of the engine with a 5 mm hex wrench. Remove the bolts holding the air cleaner hose and resonator in place with a ratchet and metric socket. Then remove the air cleaner assembly from the vehicle.

    4

    Squeeze the spring clamps holding the heater hoses to the water inlet with a pair of pliers and slide them down the water hoses. Pull the heater hoses off of the water inlet.

    5

    Disconnect the coolant temperature sensors electrical connector. Remove the nut holding the wire protector to the water inlet with a ratchet and metric socket and remove the protector from the inlet.

    6

    Remove the bolts holding the water inlet pipe to the water inlet with a ratchet and metric socket. Remove the water inlet pipe from the water inlet.

    7

    Remove the nuts holding the water inlet to the cylinder head, then remove the water inlet from the cylinder head. Remove the thermostat from the inlet.

Installation

    8

    Install a new gasket onto the new thermostat. Set the water pump inside the cylinder head opening so that the small jiggle valve on top of the in line with the top-center water inlet valve mounting stud.

    9

    Set the water inlet valve onto the cylinder head so the cylinder head studs pass through the holes in the water inlet. Install the water inlet nuts and tighten them to 69 inch-pounds with a torque wrench.

    10

    Remove the old O-ring from the water inlet pipe. Install a new O-ring on the water inlet pipe and coat it with soapy water. Install the water inlet pipe into the water inlet, then install the water inlet pipe mounting bolt into the cylinder head and torque it to 14 foot-pounds with a torque wrench.

    11

    Set the engine wire protector into position and reinstall its retaining nut with a ratchet and metric socket. Reconnect the coolant temperature sensors electrical connector.

    12

    Connect both heater hoses to the water inlet. Squeeze the spring clamps with a pair of pliers and slide them down the hoses and release the pliers when they are in their original position.

    13

    Set the air cleaner and resonator assembly into position and reinstall its retaining bolts. Set the V-bank cover into position and reinstall its retaining bolts with a 5 mm hex wrench.

    14

    Fill the radiator with a 50/50 mixture of Toyota Long Life Coolant and distilled water until it reaches the top. Replace the radiator cap and fill the coolant reservoir with the same mixture until it reaches the FULL mark. Start the engine and allow it to come up to operating temperature. Check for coolant leaks and then re-check the coolant level. Add coolant if necessary to raise the coolant level to the FULL mark on the side of the coolant reservoir.

Read More.. >

Monday, March 17, 2014

Infinity Q45 Repair Procedures

The Infiniti Q45 is a Japanese-produced rear-wheel-drive automobile. In order to ensure operator safety and maximize the life of a car, all major repairs should be carried out by a qualified professional. The owners manual of the Infiniti Q45 includes several sections providing information on when repairs should be conducted by service professionals. For example, while punctured tires can be dealt with by the car operator, problems with the Infiniti Q45s complex airbag deployment system should be dealt with by a qualified professional.

Infiniti Q45

    As of July 2011, the last model of the Infiniti Q45 was released in 2006. It features firm suspension tuning, a 4.5-liter V8 engine, an automatic transmission, 340 horsepower and 333 pound-feet of torque. The 2006 model featured active rear steering (which monitored vehicle speed and steering), 19-inch alloy wheels, a transmission with downshift rev-matching and a lane departure warning system.

Warning Lights

    In many cases, the Infiniti Q45 tells drivers when certain features on the car need to be repaired through the use of warning lights. While some warning lights, such as the low-fuel warning light and the low tire pressure warning light, indicate problems that can be fixed by the driver, other warning lights indicate problems that must be attended to by a qualified professional. These include a seat belt warning light, an airbag warning light, a transmission warning light, a break warning light, a battery charge warning light and an engine oil pressure warning light, among others. If any of these lights come on, take your vehicle to a mechanic with the required knowledge.

Windshields

    Windshields may be damaged in a variety of circumstances, such as a collision, an act of vandalism or stone being thrown up by other cars on the road. A cracked windshield is a significant safety hazard and must be replaced immediately by a qualified professional. In addition to the threat of shattering glass, a cracked windshield may also affect the deployment of the supplemental airbag system.

Airbags

    The Infiniti Q45 owners manual contains a special section on repair procedures associated with its airbag system. If the airbag warning light comes on, the system may either need to be repaired or replaced. Due to the complexity of the system, the airbag system should only be checked by a certified mechanic. Anytime there is damage to the front or side of the vehicle, the airbag system should be inspected. Any time an airbag has been inflated, the airbag system should be replaced. When working under the hood or inside the vehicle, the ignition should always be in the "lock" position.

Read More.. >

Sunday, January 26, 2014

Automatic Transmission Flush Procedures

Purchasing a brand new transmission could set you back as much as $2,000. Anything that can be done to keep your transmission operating smoothly is highly recommended. A transmission flush is one such task, and having information regarding this topic can be beneficial to vehicle owners.

Procedures

    A transmission flush is the process of replacing old transmission fluid with fresh fluid. Fluid flush machines can be used for this and are known to make the process simple and quick, taking only about 10 minutes or so to complete. The car is put in park and the engine left idling as the old fluid is swapped out for the new.

Significance

    Worn out fluid is harmful to transmissions, often resulting in them failing altogether. Old fluid becomes oxidized and fails to lubricate the transmission as well as it did when it was new. Control valves also stick due to old dirty fluid. A transmission flush eliminates all these harmful effects caused by old fluid.

Time Frame

    Flushing a transmission on a regular basis can increase the life of the transmission. It is recommended to have your transmission flushed about every 40,000 miles or so.

Read More.. >

Monday, November 4, 2013

Idle Relearn Procedures for a Chevy

Modern vehicles, such as those manufactured by Chevy, work in unison with computer modules within the engine compartment. An idle relearn procedure must be performed if a computer, or chip, is replaced in the vehicle.

Function

    An idle relearn procedure is a way to reprogram the vehicles computer memory to idle at a specified RPM, or revolutions per minute. Without the programmed idle, the vehicle can run arbitrarily, resulting in unnecessary engine wear.

Features

    Chevy uses a simple idle relearn process. After you replace the computer chip, it will automatically reset itself when you turn the ignition key from the "on" position to the "off" position. Blue Streak Electronics recommends to warm the engine after the idle relearn procedure, without use of the air conditioner. After the engine is warm, switch the air conditioning on and off, and then put the transmission into the "drive" position. These actions complete the full idle relearn procedure.

Considerations

    It is imperative that a technician verifies that the cars battery is fully charged. If power fails during a relearn procedure, the technician must reprogram the computer chip.

Read More.. >