Showing posts with label gear. Show all posts
Showing posts with label gear. Show all posts

Saturday, May 3, 2014

What Is a Gear Drive

What Is a Gear Drive?

A gear drive drive requires two gears for operation. The two gears are spur cut, and the drive gear receives force from the power output. The drive gear then transfers power to the driven gear.

Different Drive Systems

    All drive systems require a drive gear. The drive gear is the main transfer from the power source to the driven gear. A belt from the drive gear to the driven gear is a "belt driven" system. Another option is the "chain driven" system. The "chain driven" system uses a chain from the drive gear to the driven gear. The "gear drive" system is direct gear-drive. The drive gear is directly meshed with the driven gear.

Common applications

    Gear drives are used in transmissions, rear ends and transfer cases; at times the drive gear will be smaller than the driven gear. Different gear ratios enable the transmission to shift to lower or higher rpm speeds.

Automotive gear drive

    Gear drives are used on automotive engines. A "gear drive" usually ers to the timing drive; it replaces the common timing-chain with spur-cut gears. A gear drive is known for the "whining noise" it emits. The teeth of the gears mesh together as the gears turn with the rotation of the engine. This keeps the engine in time.

Read More.. >

Wednesday, March 26, 2014

How to Replace a Steering Gear

How to Replace a Steering Gear

A steering gear controls an automobiles movement and should be properly maintained on a regular basis. To find out whether you need to replace your steering gear, check the condition of the fluid and hoses. If the fluid is contaminated or the hoses are worn, replace the steering gear immediately before taking the vehicle out on the road. Check a shop manual specific to your vehicle for correct specifications.

Instructions

    1

    Disconnect and cover both of the fluid lines to stop any leakage or contamination. Mark and disconnect the steering shaft coupler. The steering shaft can only be completely removed once the steering gear is taken out.

    2

    Raise the vehicle on a car lift. Use a wrench to remove the Pitman arm from the shaft. If you dont have a car lift, then a car jack and jack stands will work just as well.

    3

    Use a wrench to remove the mounting bolts holding the gear case to the frame. Slide the steering gear away from the car. Take the steering shaft out of the vehicle.

    4

    Mount the new gear casing into the frame and secure it in place with the mounting bolts. Align the Pitman arm to the shaft and tighten it in place with the wrench.

    5

    Attach the coupler to the steering shaft and connect it to the gear casing. Reconnect the two fluid lines and replace the fluid. Find a quiet road to test the steering gear before taking the vehicle out on a busy thoroughfare.

Read More.. >

Wednesday, March 5, 2014

How to Remove the Gear Shift on a Manual Transmission Ford F 150

How to Remove the Gear Shift on a Manual Transmission Ford F-150

A Ford F-150s gear shift is simple to remove. It is also a repair procedure that doesnt require disabling the F-150s airbag system, unlike many of the components located in the dashboard. There are two major reasons why you might consider doing this. If youre revamping and customizing the F-150s interior, the shift lever boot, the lever and the knob likely have aftermarket options to consider. On a more pragmatic level, you will need to remove the gear shifter entirely if you are going to access and work on the manual transmission.

Instructions

    1

    Remove the shift boots four retaining screws located at each corner of the boot. You will have to lift up the corner to get at the screws.

    2

    Pull the boot directly upward to expose a nut and bolt on the lever. You do not need to remove the boot completely from the lever. So you can leave the shift knob alone.

    3

    Unscrew the nut with a socket wrench. Then push the threaded side of the bolt through the lever. Grab the bolt by its other side and pull it out of the shift lever.

    4

    Remove the lever from the square mounting boot beneath it.

Read More.. >

Sunday, October 13, 2013

How to Determine GMC Gear Ratio

The gear ratio of a vehicle determines whether the vehicle will have more low end power or high end speed. A vehicle that has a lower gear in the rear differential usually gets less fuel mileage, whereas a vehicle with higher gears tend to get better fuel mileage because the engine turns less revolutions per minute. The lower the gear ratio number the higher the gear ratio. Most manufacturers gear their vehicles for maximum performance and mileage. To determine the gear ratio of a GMC or any vehicle the task is accomplished the same way.

Instructions

Raise the Vehcile

    1

    Park the vehicle on a level surface. Insert two wheel blocks, one on the front side of each front wheel.

    2

    Place a floor jack in the center of the rear differential and raise the rear wheels off the ground.

    3

    Set two more wheel blocks, one on the back side of each front wheel, to ensure the vehicle cannot move.

    4

    Spot two jack stands, one near each wheel, under the rear axle tubes.

Determining the Gear Ratio

    5

    Wrap a thin, flexible tape measure around the driveshaft tube near the rear yoke. Accurately measure the circumference of the shaft. Record the measurement.

    6

    Clamp a piece of coat hanger wire to each of the remaining two jack stands to use as a pointer. Use one jack stand as a pointer placed next to the rear tire. Make a corresponding mark on the tire sidewall that aligns exactly with the wire pointer on the jack stand. The pointer is needed to accurately record exactly one wheel rotation.

    7

    Clamp the end of the 16-gauge yellow electrical wire tight to the driveshaft with a hose clamp around the 6 o clock or 9 oclock position on the shaft. Bend and pull the yellow wire down perpendicular to driveshaft so the wire will be drawn up when the shaft rotates.

    8

    Mark the yellow wire, with a permanent marker, where it comes out from under the hose clamp -- this will be the starting point. Spot the other jack stand next to the driveshaft with the wire pointer aimed directly at the starting point mark on the wire.

    9

    Turn the key on, just enough to unlock the wheel and place the shifting lever in neutral so the driveshaft can be rotated.

    10

    Rotate the driveshaft in the direction that winds the yellow wire up perpendicularly onto the shaft like a winch cable on a winch. Keep the wire tight and the wraps tight to each other.

    Stop rotating the driveshaft when the wheel turns exactly one turn. Make a mark on the last wrap of the yellow wire that aligns with the pointer on the jack stand near the driveshaft -- this will be the end mark.

    11

    Unscrew the hose clamp from the driveshaft. Remove the yellow wire and measure the distance accurately between starting mark and the end mark.

    12

    Divide the length of the yellow wire in inches by the length of the driveshaft circumference in inches; that figure is the gear ratio.

    For example: The wire measured 42.375 inches. The circumference of the driveshaft measured 10.625 inches.

    Divide 42.375 by 10.625-inches and it equals 3.988. Rounded off it makes a 3.99 gear ratio, which means that the driveshaft turns 3.99 times for each one turn of the wheel.

    13

    Remove the tools from under the vehicle and the jack stands from under the rear axle tubes. Lower the vehicle back onto the ground.

Read More.. >