Showing posts with label 96. Show all posts
Showing posts with label 96. Show all posts

Saturday, May 17, 2014

How do I Install Tie Rod Ends on a 96 Honda Accord

How do I Install Tie Rod Ends on a 96 Honda Accord?

Your 1996 Honda Accords tie-rod ends are the steering components that attach the steering linkage and linkage parts to the steering knuckles with a hardened steel ball stud. A tie-rod end can be replaced alone, but many automotive parts manufacturers recommend replacing the entire tie-rod as a whole and often sell these components fully assembled. You may want to purchase just the tie-rod ends, if available, if you are looking to conduct this repair method. This procedure does not require special tools and can be done at home with little automotive experience or knowledge.

Instructions

Removing the Tie-Rod Ends

    1

    Unscrew the lug nuts on your Accord slightly, then raise your Accord and support it with jack stands.

    2

    Remove the lug nuts and take the front wheels off.

    3

    Loosen the jam nut using one open-end box wrench while holding onto the tie-rod end with another. When the thread is exposed, mark it with some correction fluid to erence the new tie-rods position.

    4

    Take out the cotter pin on the tie-rod end stud and loosen the nut, but dont remove it.

    5

    Pry the tie-rod end from the steering knuckle arm using a two-jaw puller. Now remove the nut and separate the tie-rod end from the steering knuckle arm.

    6

    Separate the tie-rod end from the tie-rod by unscrewing it.

Installing the New Tie-Rod End

    7

    Screw on the tie-rod end up to the marked point on the tie-rod; you may need your open-end wrench. Place the tie-rod stud into the steering knuckle arm.

    8

    Screw on the nut to the tie-rod end stud and torque it to 32 foot-lbs with your torque wrench. Install the new cotter pin.

    9

    Repeat all steps in each section for the other side of your Accord.

    10

    Install the wheels and screw on the lug nuts finger tight. Lower your Accord and torque the lug nuts to 80 foot-lbs.

Read More.. >

Sunday, May 4, 2014

How to Change a 96 Ford E350 Fuel Pump

The Ford E-Series is a line of full-size vans that has been in continuous production since 1961. The number in the series indicates the carrying capacity of the van, such that 350 indicates a carrying capacity of one ton. All versions of the E350 use electronic fuel injection, which requires the fuel pump to maintain the fuel system under high pressure. You must remove the fuel tank on the 1996 Ford E350 to replace the fuel pump.

Instructions

    1

    Detach the electrical connector for the fuel pump relay in the engine compartment and engage the starter for 10 seconds to empty the fuel system. Attach the electrical connector for the fuel pump relay. Disconnect the negative battery cable with a socket wrench to ensure you dont start the engine inadvertently while replacing the fuel pump. Siphon the fuel from the fuel tank with a hose and drain the fuel into a gasoline container.

    2

    Raise the vehicle and support it on jack stands. Disconnect the electrical connector for the fuel pump assembly and detach the fuel lines from the fuel tank. Support the fuel tank with a floor jack and disconnect the filler tube retainers with a socket wrench. Remove the straps for the fuel tank and lower the fuel tank with the floor jack. Move the fuel tank to your work area.

    3

    Clean the fuel tank around the fuel pump assembly with a shop towel to keep dirt out of the fuel tank. Turn the locking ring on the fuel pump assembly counterclockwise with a locking ring adapter for a 1996 Ford E350. Remove the locking ring from the fuel pump assembly and pull the fuel pump assembly out of the fuel tank. Discard the old gasket on the fuel tank.

    4

    Clean the mounting flange for the fuel pump assembly with a shop towel and coat the mounting flange with a thin layer of lubricant meeting Ford specification ESA-M1C75-B. Install the new gasket and fuel pump assembly into the fuel tank. Place the locking ring onto the fuel pump assembly and turn it clockwise until it locks into place.

    5

    Install the fuel tank by performing Step 2 in reverse and fill the fuel tank with fuel. Connect the negative battery terminal with a socket wrench. Turn the ignition on to pressurize the fuel system.

Read More.. >