Tuesday, April 1, 2014
How do I Troubleshoot a Defroster on a 79 Oldsmobile
You can troubleshoot the defroster in a 1979 Oldsmobile yourself without the headache of finding a mechanic and having to make a decision about repairs on the spot. There is a possibility you might need a voltmeter to troubleshoot your vehicle. This can be purchased at any auto parts store.
Instructions
- 1
Check the cars coolant level. The warm air from a car defroster comes from the engines coolant. A low engine coolant level could be causing a lack of heat from the defroster. Also check that the heater core is not plugged. The coolant flows through the heater core to warm the defroster.
2Check to see if the vacuum hose is detached or damaged. If it is, this can keep the doors from working and cause a lack of control in air direction. Ducts are responsible for moving the heater core air into the passenger cabin of the car. Vacuum-powered doors are responsible for the direction of air flow inside the ducts in most vehicles. Check the cabin air filter, too. If the cabin air filter is full of debris, this can also lead to a reduced flow of air.
3Use the car manual as a guide to find the fuse box and also to learn the proper positioning for the blower fuse. Check inside the fuse box to assess the blower fuse. Use the voltmeter to make sure the blower is grounded and can receive power if the fuse is undamaged.
Friday, February 28, 2014
How to Repair a Window Defroster
Window defrosters operate by conducting small amounts of electricity along conductive strips taped to the window. You are left with a window that will not defrost fully when one of the strips fails. Total system failure implies that you blew a fuse, which is a 20 cent repair. However, a damaged strip requires locating the impacted area and repairing it. Repairing the defroster means repairing the grid or strips running along the window or reattaching the electrical connection on the side of the glass.
Instructions
Repairing the Grid
- 1
Test the grid (the thin metal strip running horizontally across your window). Turn the ignition to "ON" and turn on the rear defrost. Place one terminal of the multimeter (set to DC volts) on the grid at the center of the line and the other on the thick vertical strip to which the grid connects. The multimeter should read six volts when testing from the center of the grid line to the side. A reading of 12 volts indicates the damaged section is between the terminals.
2Bring the terminals closer together. Monitor the reading as you do. Isolate the section of the grid that reads 12 volts. This section is your damaged area that needs to be repaired. Mark both sides of the damaged area with a grease pencil. Repeat Steps 1 and 2 with the remaining grids marking any damaged areas.
3Transpose the marks to the exterior of the window. Trace the line with a straight edge and a grease pencil.
4Clean the window thoroughly first with glass cleaner and paper towels and then with rubbing alcohol and paper towels.
5Place strips of masking tape above and below the area to be repaired so that you have a straight line after painting it.
6Paint the strip using the conductive paint from the grid repair kit. Shake the bottle vigorously and apply two coats. Wait five minutes before applying the second coat and two more minutes before removing the masking tape.
Repairing the Electrical Connection
- 7
Disconnect the electrical connection from the wiring harness.
8Clean the area of the damaged electrical connection with window cleaner and then rubbing alcohol. Use a flat head screwdriver to smooth out any bumps or old glue spots before cleaning.
9Place a few drops of the adhesive to the back of the electrical connection and firmly press into place. Hold the unit in place for a minute and release. Allow the section to set for 24 hours and reconnect the electrical harness.
Sunday, November 24, 2013
My Defroster Wont Stay On
A defroster that wont stay on when activated may lead to an accident due to poor road visibility. This is because it is supposed to prevent fog, frost or ice buildup in your cars window. Determining the cause of a malfunctioning defroster requires initial troubleshooting steps. In most cases, the problem requires a fairly easy fix that you can perform on your own. However, a more serious case is still best attended by a professional.
Instructions
- 1
Inspect the defrosters fuse to determine if it is causing the problem. As the location of the defroster depends on the cars manufacturer, make and model, consult your owners manual to confirm where you can find the fuse. Once located, use a volt meter to check if the fuse is working or not.
2Examine the wiring from the fuse box to also ensure that there is proper connection. Make sure that the fuse is tight and secure as a loose one may also be causing the problem. Use an electrical tape in case there are parts of the wiring needing coverage.
If the fuse is causing the problem, simply follow the more specific steps indicated in the owners manual for the replacement. Ideally, this requires pulling out the old one with the fuse puller in your fuse box, then simply attaching a new fuse, which is easily available in auto stores.
After checking the fuse and its components and there seems to be no problem, proceed to the next steps for further troubleshooting.
3Check the wire that goes directly to the defroster as the tab typically connected to it can get detached in time. Make any fix using a window defroster tab adhesive, if necessary. Such adhesive, usually available in auto shops and super centers, comes in a kit with instructions on how to use it.
4Examine the defroster grid lines found on the window. Make sure the glass heating the grid feed and the ground wires are properly connected to the glass. To make a do-it-yourself fix for any minor damage, use a window defogger repair kit and follow the instructions indicated in the package.