Showing posts with label gen. Show all posts
Showing posts with label gen. Show all posts

Tuesday, March 11, 2014

How to Identify GM Gen III Engines

How to Identify GM Gen III Engines

GM Generation III small block engines, also known as LS1s, made their debut in the 1997 Corvette. According to "Engine Builder" magazine, Generation IIIs replaced the LT1 series. They have a smaller block, are lighter in construction and generate more horsepower than LT1s. Identifying Generation III engines is similar to other GM engines; begin visually, then locate the engine block casting number to be thorough. Although the LS1 identifies the engine family, it actually consisted of the LS 1 through 7, the L89 and C33. Truck versions of the Generation III were called "Vortec."

Instructions

    1

    Determine if the year and make of the vehicle are possible Generation III candidates. According to LS1 Engine, Generation III engines were used in 1997 to 2004 Corvettes, 1998 to 2004 Camaro SS and Z28 models, 1998 to 2002 Pontiac Firebirds, the 2004 Pontiac GTO and numerous GM Truck, van and SUV applications.

    2

    Inspect the engine compartment. GM often put identifying decals and tags on the engine itself or in the compartment area. These may indicate the use of a Generation III engine. Also try to determine if the block is aluminum or cast-iron. According to "Hot Rod" magazine, most automobile LS1s were aluminum, while truck versions were cast-iron. Aluminum blocks will have a smooth finish as opposed to the rough grain of cast-iron.

    3

    Locate the casting number on the engine block. "Hot Rod" places it on the drivers side, just below the cylinder head. It is an eight-digit number.

    4

    Decode the casting number by comparing it to a casting number listing, similar to the one found on Fastnuf (see Resources). This listing will give the specifics of the engine in question when matched to the casting number.

Read More.. >

Monday, October 28, 2013

How to Install the Fuel Injectors for a Gen III Engine

The LS series of engines are manufactured by General Motors for use in its rear-wheel drive vehicles. The third generation of these engines, also known as Gen III engines, were in production from 1997 through 2007. They appear in many different vehicles from General Motors, such as the Chevrolet Camaro produced from 1998 through 2002. The Gen III engine uses electronic fuel injectors to deliver fuel to the engine under high pressure.

Instructions

    1

    Remove the cable from the negative battery terminal with a socket wrench so you dont accidentally start the engine. Open the filler cap on the fuel tank to relieve the pressure in the fuel tank.

    2

    Wrap a shop rag around the pressure valve on the fuel rail and attach a fuel pressure gauge to the valve. Put the bleed hose of the fuel pressure gauge into a gasoline container and open the valve to relieve the pressure in the fuel system.

    3

    Disconnect the fuel line from the fuel rail. Remove the accelerator cable and its bracket from the engine compartment with a socket wrench. Detach the electrical connectors from the fuel injectors and fuel rail.

    4

    Remove the fuel rail and fuel injectors from the intake manifold as an assembly with a socket wrench. Spread the retainer clips for the fuel injectors apart and remove the fuel injectors from the fuel rail. Discard the retainer clips and O-rings on the fuel injectors.

    5

    Coat the O-rings for the fuel injectors with engine oil and mount them to the fuel injectors. Install the new fuel injectors onto the fuel rail with the electrical terminals on the injectors facing outward. Attach new retaining clips to the fuel injectors.

    6

    Connect the fuel rail assembly to the intake manifold and tighten its mounting bolts to 89 inch-pounds with a torque wrench. Attach the electrical connectors for the fuel rail and fuel injectors. Install the accelerator cable and its bracket with the socket wrench. Attach the fuel lines to the fuel rail and tighten the fittings.

    7

    Reattach the cable to the negative battery terminal with the socket wrench and fasten the filler cap onto the fuel tank. Turn the ignition on for two seconds to pressurize the fuel system then turn it off for 10 seconds. Turn the ignition back on and check for any fuel leaks.

Read More.. >