Thursday, May 15, 2014
Installing a Thermostat on a 1988 Buick LeSabre 3 0
The thermostat on the 1988 Buick LeSabre is located partially inside the intake manifold and the thermostat housing. Because the thermostat sits higher than the fluid level in the radiator, replacing the thermostat in the LeSabre is an uncomplicated task. Fortunately, the thermostat housing is not hidden among engine accessories. This makes it easier to reach, remove and replace a broken thermostat.
Instructions
- 1
Follow the upper radiator hose to the point where the hose connects to the LeSabres engine. The metal connector to which the hose connects is the thermostat housing.
2Disconnect the radiator hose from the housing by squeezing the pressure tabs on the radiator hose clamp together with a pair of pliers. With the pressure released, pull the hose off the housing. A small amount of fluid may run onto the engine block. To minimize this, hold the hose vertical for a few seconds to drain the fluid back into the radiator.
3Remove the two bolts that secure the thermostat housing to the Buicks intake manifold with a 7/16-inch socket and ratchet. With the bolts removed, apply pressure on the side of the housing with the ball of your hand to break the seal between the housing and the intake.
4Pull the old thermostat out of the intake manifold and plug the hole with a shop towel to prevent anything from getting into the coolant system of your Buick.
5Scrape all the old gasket material off the bottom of the thermostat housing and the mating surface of the intake manifold. Brush off any debris with a shop towel.
6Remove the shop towel from the intake manifold and place the new thermostat into the hole. The end with the large spring submerges into the intake manifold and the end with the pin sits inside the thermostat housing.
7Place a thin bead of RTV gasket maker on the bottom edge of the thermostat gasket. Allow the RTV gasket maker to firm up for approximately 20 minutes. This creates a small layer of "skin" on the RTV.
8Place the thermostat housing onto the intake manifold and bolt it into place. Do not wipe off any excess RTV. It serves as additional sealant.
9Squeeze the pressure tabs on the radiator hose clamp. With pressure released, slide the hose onto the thermostat housing and then let go of the tabs.
Thursday, February 20, 2014
How to Detect Bad Struts in a 2005 Buick LaCrosse
As vehicles age, many components wear out, and struts are no exception to this rule. Each time that you drive your vehicle, the struts are moving up and down many times per second to absorb road vibrations. This constant movement, along with certain environmental factors, causes the struts to wear out. The most common symptom of bad struts is a noticeably rough ride, especially when going over bumps or uneven pavement. In addition to noticing the ride, there are other ways that you can detect bad struts in your vehicle.
Instructions
- 1
Test drive your vehicle on the side streets as well as the highway. Purposely drive over bumps, cracks, and uneven spots in the road and take note of the vehicles reaction to these irregularities. In a vehicle with bad struts, youll notice a harsh, jarring ride when going over the bad spots in the pavement. In a vehicle with good struts, the rebound will be smooth, controlled and feel tight, as opposed to sloppy, harsh, and loud.
2Press down quickly on the vehicles bumper with two hands, and then let it up. The vehicle should lift back to its normal height without excessive rebound, or bouncing. If the vehicle bounces and reverberates, the struts are likely bad. This is because the struts are designed to minimize the rebound vibrations from the springs.
3Look at the odometer and note the vehicles mileage. The performance of most vehicle struts greatly diminishes after about 60,000 miles. If youve got more mileage than that on your car and the struts are original, its a good time to replace them.
4Inspect your tires for uneven wear. Faulty struts allow tires to wear unevenly, causing cupping. Cupping ers to the tires having intermittent, parallel worn spots across the tire, creating high and low spots on the tire.
5Lift the vehicle with an automotive jack and then support it with jack stands. Place wheel chocks behind the opposing wheels. Shine a work light up under the wheel well and look at the strut cartridge or tube; it should be dry with no signs of fluid leakage. Most modern struts are gas charged and also contain hydraulic fluid. When struts age, their seals begin to leak this fluid. Once the fluid begins to leak, the strut is already ruined and its performance is dramatically decreased.
Monday, November 25, 2013
How to Replace Fuel Pumps in a 1995 Buick LeSabre
The Buick LeSabre was a series of full-size cars that the Buick division of General Motors produced from 1959 to 2005. The 1995 Buick Lesabre was a 4-door sedan with a 6-cylinder 3.8-liter engine. This engine used sequential fuel injection to deliver high-pressure fuel to the fuel injectors. The fuel pump in the 1995 Buick LeSabre was in the fuel tank, requiring you to remove the fuel tank when replacing the fuel pump.
Instructions
- 1
Disconnect the negative terminal on the battery with a socket wrench to avoid starting the engine accidentally. Open the fuel filler cap to relieve the vapor pressure in the fuel tank. Remove the cap for the fuel pressure fitting on the fuel rail, and wrap a shop towel around the fuel pressure fitting. Attach fuel pressure valve J 34730-1A to the fuel pressure fitting, and place the bleed hose into container approved for gasoline. Open the valve to release the pressure in the fuel system, and fasten the fuel filler cap.
2Raise the vehicle with a jack and support it on jack stands. Disconnect the filler vent hose from the fuel tank and connect the open end of the hose to a hand-operated pump. Drain as much fuel from the fuel tank is possible into a gasoline container.
3Detach the electrical connector for the fuel sender and remove the fuel lines from the fuel sender. Disconnect the quick connectors for the fuel pipe and support the fuel tank with jack stands. Remove the bolts for the fuel tank retaining straps with a socket wrench and disconnect the rear hangar of the exhaust system. Disconnect the fuel tank and remove it from the vehicle.
4Turn the locking ring for the fuel sender assembly counterclockwise with tool J-24187. Lift the fuel sender assembly carefully from the fuel tank, detach the fuel pump from the fuel gauge sender unit. Discard the O-ring on top of the fuel sender. Disconnect the electrical connector for the fuel comp, and release the clamps around the fuel pump. Pull the fuel from its rubber connectors.
5Install the new fuel pump by performing Steps 2 through 4 in reverse, ensuring that you also install a new O-ring. Fill the fuel tank, and connect the negative terminal on the battery with a socket wrench. Turn the ignition on to pressurize the fuel system, and check for fuel leaks.
Tuesday, September 24, 2013
How to Replace the R134 in a Buick
R134 refrigerant replaced the old R12 Freon as an environmentally friendly alternative for powering automotive air conditioning systems in the late 1990s. While replacing the R134 isnt a necessary operation, you may need to evacuate and recharge the AC system in order to perform a leak repair or replace a failed component. There are special service machines specifically designed to work with R134 air conditioning systems, which are not readily available to the general population. With that in mind, its best to leave this repair to a certified professional.
Instructions
- 1
Open the Buicks hood and locate the AC service port caps, one red and one blue (usually), located on the silver AC manifold lines and the silver receiver/dryer tank. Remove the caps by hand to expose the AC service ports.
2Attach the color-coordinated AC service hoses from the AC service machine to the AC service ports. Tighten the service hoses onto the ports by hand.
3Evacuate the Buicks AC system with the AC service machine following the machines specific user guide. This procedure will vary according to the year, make and model of your AC machine, but it normally involves setting the switches or dials to the evacuation setting.
4Vacuum test the Buicks AC system with the AC service machine following the machines user guide to make sure there are no leaks.
5Recharge the Buicks AC system with the AC service machine following the machines specific user guide. Disconnect the AC service hoses. Reinstall the service port caps and close the hood.