Thursday, April 24, 2014
How to Repair RV Springs
Traveling in an recreational vehicle (RV) is a fun and enjoyable way to see the country. RVs are stocked with everything you need to live on the road; as such, they have toilets and showers, beds and furniture, rigerators, stoves and, yes, even the proverbial kitchen sink. All these household items make an RV weigh a lot, which in turn places greater wear on an RVs suspension components. The suspension part that gets the most abuse is the coil spring, as it is constantly being torqued while the RV is in motion and under constant stress from the weight of the RV itself.
Instructions
- 1
Raise your RV with an RV jack. Do not use a normal car jack, as the greater weight of a RV can break a car jack. Lift the RV up until the wheel whose suspension you want to work on is no longer in contact with the ground and rotates freely. Once the wheel is in the air, if the RV suspension spring has broken in half or more, you can remove the pieces by hand, as the springs are normally held in place via the pressure of the RV on the spring itself. Use work gloves to remove the spring, as the spring may have ragged metal edges if it has broken.
2Remove the RV wheel with a nut removal tool; your RV should have come with one. If you need additional torque, use a power tool with a nut-removal bit. Be caul when removing the wheel, as RV wheels can weigh substantially more than car wheels depending upon your RVs make and model.
3Remove the brake pad assembly with a Phillips-head screwdriver. Some RVs may use a drum assembly; you still use a Phillips-head screwdriver to remove it. Caully support the brake assembly when removing it, as its weight can rip off the brake lines. Just set the brake assembly on a stool, elevated, so that you do not have to go through the hassle of flushing the brake system and reattaching lines.
4Remove the spring by pulling down on the control arm to its full extension and wedging a flat-head screwdriver between the suspension arm and the spring. Wiggle the coil off with back-and-forth rocking motions. Wear safety goggles in case the spring jumps off the control arm.
5Replace the spring with a new spring by again pulling the control arm down to its fullest extension, with a flat-head screwdriver as a wedge. The spring will naturally push into place around the attachment point. Reattach the brake assembly, then wrench the wheel back on.
Tuesday, October 29, 2013
How to Install Adjustable Coilover Springs
Coilover springs really are small coil springs mounted over shock absorbers. Once the coilover kit is in place, the coilover springs become part of the shock and share the same mounting points. Together they take up very little space and the springs are easy to change and adjust. Coilovers have been used in auto racing for many years. The only downfall to installing coilover springs is that the mounts must be strong enough to withstand the abuse of a racetrack or a rough road. On race cars, the chassis builder uses strong materials to construct a strong mount.
Instructions
- 1
Determine the spring rate needed for the coilover spring. The farther out the coilover mounts, the lower the spring rate needed.
2Install the threaded coilover sleeve onto the shock housing. The threaded sleeve normally fits over the shock and is held in place by a large snap ring that fits in a groove on the shock. Some coilover shock components have the threaded sleeve made into the shock absorber housing.
3Thread a coilover spring collar onto the threaded shock sleeve. This will hold the coilover spring and is used to adjust ride height. Install the coilover spring onto the sleeve and insert a coilover spring cap on the rod end of the shock. Turn the coilover spring collar to adjust the spring rate on the shock component.
4Block the wheels on the vehicle. Place a jack under the car and raise it to take the weight off the wheel. If an old shock is on the car, remove it to make room for a coilover spring and shock component.
5Install the coilover component by bolting the shocks rod end to the bottom shock mount and inserting a bolt. Install the tube end of the shock to the top shock mount and insert a bolt. Tighten the bolts. The shock mounts upside down on a race car to reduce the unsprung weight, which is a big deal when racing. If the coilover spring is mounted on a regular car, mount it upside down -- this will keep dirt and debris off the shock rod and keep it from pitting.
6Thread the coilover collar up the threaded shock sleeve to tighten the spring and raise the cars ride height. The tighter the spring is, the more weight it will hold and the higher the ride height of the car will be.
Sunday, October 27, 2013
How to Measure for Leaf Springs
Obtaining correct leaf spring measurements is vital to keep a suspension system functioning safely and correctly. Three measurements determine if a new leaf spring will mount on a vehicle without disrupting its axle location or cause problems with its ride. The straightforward approach of measuring the straight line distance between the mounting points of the spring seem like the correct approach, but more factors come into play that determine where to take the measurements.
Instructions
- 1
Lay a steel rule flat on top of the longest spring. Align the end of the steel rule with the center of the left side leaf spring mounting bracket. Push the steel rule towards the spring to bend it to the curvature of the spring. Read the measurement from the center of the mount to the center bolt holding the leaf spring pack together.
2Switch the steel rule to the right side of the leaf spring. Repeat the ruler alignment and measuring procedure to determine the distance from the right side to the center mounting bolt.
3Add the two measurements together to determine the overall length of the leaf spring.
4Tie a string line to the left leaf spring mounting point. Pull the string line across the leaf spring. Tie the string line to the right spring mounting point. Adjust the string until both tied ends of line align with the center of the mounting points.
5Push the zero end of the rule against the leaf spring at the center bolt. Read the point the string line intersects the rule to measure the spring arch.