Showing posts with label bolts. Show all posts
Showing posts with label bolts. Show all posts

Monday, November 17, 2014

How to Fix Exhaust Manifold Broken Bolts

Nothing can be more frustrating than a broken-off bolt on your vehicles exhaust manifold. Not only is this putting stress on the rest of the attaching bolts for the manifold and the manifold itself, dangerous carbon monoxide could be escaping from the manifold and working its way into the passenger compartment. It is very important that you correct a broken exhaust manifold bolt from a mechanical as well as a safety standpoint.

Instructions

    1

    Use penetrating fluid on all of the exhaust manifold bolts, including the broken one. Let the penetrating fluid work in for several hours.

    2

    Loosen the remaining exhaust manifold bolts. Give the bolts another dose of penetrating fluid if one or more bolts still will not budge. Allow the fluid to soak in for an hour or so. Apply some heat with a propane torch if you still have any stuck bolts. Concentrate the heat onto the center of the stubborn bolt until it is red hot. Allow the bolt to cool then loosen and remove it.

    3

    Remove the exhaust manifold to reach the broken bolt. Try using vise grips or an easy-out tool to twist the bolt out if part of the bolt is protruding from the engine block. Drill the bolt out if it is broken off flush with the engine block. Use a drill bit the same diameter as one of the exhaust manifold bolts without the threads.

    4

    Run a tap into the hole that is the same size as the exhaust manifold bolts to clean out any remaining remnants of the broken piece. Tap the remaining manifold bolt holes while you are at it to ensure the bolts will thread back in smoothly.

    5

    Replace the broken bolt with one of the same size and strength as the original. Take one of the good bolts to an auto parts or hardware store to make sure you get the correct replacement. Clean up the rust on the threads of the original bolts that you are going to reuse. Use a wire brush or a wire wheel installed on a bench grinder for this task.

    6

    Scrape off any remaining gasket material from the engine block and the exhaust manifold mounting surfaces with a gasket scraper or a putty knife. Install a new exhaust manifold gasket between the exhaust manifold and the engine block. Run in the manifold bolts finger tight. Tighten the bolts with a torque wrench. Find the torque specifications for your specific model in a shop manual or from your car dealers service department.

    7

    Start your vehicle and check for exhaust leaks.

Read More.. >

Friday, December 6, 2013

How to Loosen Exhaust Bolts

How to Loosen Exhaust Bolts

The bolts connecting the components of your vehicles exhaust system are prone to rust. When rust fills the small gap located between the threads of each bolt and the threads of each bolts hex nut securing the bolt to the exhaust, the bolt and nut can fuse. That can make it difficult to loosen the nuts to work on your exhaust, or it can cause you to break the bolt altogether. Heating the bolt to get it off is a bad idea: Extremes in temperature can effectively break the bond between the two fasteners; also, when using heat you run the risk of creating a fire around the vehicle or igniting fumes from the fuel system. A safer alternative to heat is to "super-cool" one fastener.

Instructions

    1

    Remove large rust scaling from each exhaust bolt by tapping the bolts with a hammer and running a wire brush back and forth across the threads of each exhaust bolt. Clean the loose rust particles from each bolt with a clean rag.

    2

    Shake a can of freezing penetrating oil according to the cans usage instructions.

    3

    Hold the nozzle of the spray can 2 to 3 inches from the threads of the exhaust bolt. Spray the penetrating oil on the bolt for five to 10 seconds. Allow the penetrating oil to sit on the fastener for one to three minutes.

    4

    Choose a socket from a socket set that matches the size of the hex nut connected to the exhaust bolt and atach the socket to a breaker bar. Turn the nut on the exhaust bolt counterclockwise with the breaker bar. Spray additional freezing penetrating oil on the threads of the exhaust bolt if the nut does not break free.

    5

    Push hard counterclockwise with the breaker bar to snap the exhaust bolt if the nut will not work free with the penetrating oil.

Read More.. >

Thursday, December 5, 2013

How to Replace Hub Bolts

How to Replace Hub Bolts

Hub bolts connect the wheels to the hub assembly. These bolts can occasionally get stripped or bent, requiring removal and replacement. It helps if you have some auto-repair experience, but even if you dont you should be able to tackle the job. In some applications its easier to replace the entire wheel assembly than to attempt to replace just the hub bolts. However, for some vehicles, the wheel assembly may be permanently attached or a replacement may not be readily available.

Instructions

    1

    Break the lugs for the wheel that needs replacement hub bolts, using the breaker bar and lug socket. Block up a wheel to ensure that the tires wont roll when the vehicle is lifted. Use the hydraulic lift to pick the vehicle up at a structural point. Place the jack stands under structure points and lower the lift until the vehicles weight is distributed between the lift and the jack stands.

    2

    Remove the lugs and wheel. Place the lugs inside the wheel and slide the wheel underneath the vehicle. Use the hex key set to remove the retainer bolts from the brake caliper. Slightly tap the caliper with a hammer to loosen it from the rotor.

    3

    Grasp the brake rotor and pull it loose from the wheel assembly. Place the 35 mm hub socket on the wheel hub nut and remove it with the breaker bar. Remove the hub nut and pull the hub assembly off the suspension column. Use the hammer and the hammering pin to beat the hub bolts from the front. Replace with new hub bolts by hammering them in from the back until the strike plate is even with the back of the hub assembly.

Read More.. >

Saturday, October 19, 2013

How to Measure Lug Bolts

How to Measure Lug Bolts

Professionals use a bolt pattern gauge to measure lug bolts on a vehicle so they can determine what size wheel will fit. Even if you dont have a gauge, you can still measure your bolts with a regular ruler. Companies list wheel sizes in the format "4x4.5," where the first digit is the number of lug bolts and the second number is the diameter of a circle drawn through the middle of the bolts, expressed in inches or millimeters.

Instructions

    1

    Count the number of lug bolts on your vehicle. If it has five lug bolts, youll need to measure differently than if it has four, six or eight.

    2

    Lay a ruler across the ends of the lug bolts and measure from the center of one lug bolt to the center of the lug bolt directly across from it, if you have an even number of lug bolts. If you have five lug bolts, measure the first and third bolt, from the center of one to the outer edge of the other.

    3

    Convert the measurement from inches to millimeters, if necessary. Express the result in inches as a decimal by dividing out the fraction and adding it to the whole inches. Multiply the result by 25.4 to convert to millimeters. For example, to convert 4 5/8 inches, divide 5 by 8 to get .625. Add that to 4 to get 4.625, then multiply it by 25.4 to get 117.48 millimeters.

Read More.. >